1 / 4
Dachlüfter für Wohnwagen - Roof vent for caravans — zdjęcie 1
1 / 4

Dachlüfter für Wohnwagen - Roof vent for caravans

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Aus einem passiven kleinen Wohnwagen-Dachlüfter (Pilzlüfter) wir ein aktiver Lüfter mit elektrischem Ventilator.

Ocena
0 / 5
Polubienia
4
Pobrania
29
Wydruki
0
Wyświetlenia
322
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial

Der Luftdurchsatz eines kleinen Pilzlüfters ist sehr gering. Speziell in Bad/Toilette eines Wohnwagens reicht das nicht aus. In meinem Fall handelt es sich um den serienmäßigen Dachlüfter in einem neuen, kleinen Sterckeman - Wohnwagen (baugleich mit Caravelair). Die Öffnung im Dach hat Durchmesser 100 mm. Der Teilkreisdurchmesser der 3 vorhandenen Schrauben ist ca. 91 mm. Das letzte Bild zeigt den passiven Lüfter vor dem Umbau. Mit folgenden Teilen habe ich daraus einen aktiven Lüfter gebaut:

  1. Das vorhandene Oberteil (Pilz) wird weiter verwendet (Hersteller unbekannt).
  2. Das vorhandene Unterteil wird durch Teil 1 ersetzt.
  3. Die 3 vorhandenen Schrauben werden dafür weiter verwendet.
  4. Ein PC-Lüfter 80 x 80 mm mit möglichst hohem Luftdurchsatz, möglichst geräuscharm durch integrierte Entkopplung.
  5. Teil 2 kommt unter den Lüfter und bietet auch Platz um nicht benötigte Kabellänge des Lüfterkabels aufzunehmen.
  6. Am Teil 2 befindet sich eine ebene Fläche, um einen Drehzahlregler für PC-Lüfter anzubringen.
  7. Mit 4 Spax-Schrauben 3 x 40 mm mit Senkkopf werden Teil 2, der PC-Lüfter und Teil 1 zusammengehalten.

Der elektrische Anschluss muss natürlich durch eine fachkundige Person durchgeführt werden.

The air flow rate of a small dome vent is very low. This is not sufficient, especially in the bathroom/toilet of a caravan. In my case, it is the standard roof vent in a new, small Sterckeman caravan (identical in construction to Caravelair). The opening in the roof has a diameter of 100 mm. The pitch circle diameter of the 3 screws is about 91 mm. I used the following parts to build an active fan:

The existing upper part (dome) is still used (manufacturer unknown).
The existing lower part is replaced by part 1.
The 3 existing screws are still used.
An 80 x 80 mm PC fan with the highest possible air flow rate and as little noise as possible (integrated decoupling).
Part 2 goes under the fan and also provides space to accommodate any excess length of fan cable.
Part 2 has a flat surface for attaching a speed controller for PC fans.
Part 2, the PC fan and part 1 are held together with 4 Spax screws 3 x 40 mm with countersunk heads.

The electrical connection must, of course, be carried out by a qualified person.

Translated with DeepL.com (free version)

Tagi