1 / 3
2025 Ford Maverick Front License Plate Mount (No Drill) — zdjęcie 1
1 / 3

2025 Ford Maverick Front License Plate Mount (No Drill)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Wstępna wycena dla PETG

3,29 € – 4,03 € netto (bez VAT)

Dla pliku: Maverick License Plate Grill Mounts.bgcode

To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.

Plik i założenia wyceny

Plik użyty do wyceny

Średnia wycena orientacyjna: 3,66 € netto (środek widełek).

Masa podana przez autora
71 g
Czas druku podany przez autora
2,68 godz.
Materiał u źródła
PET
Materiał wyceny
PETG
Drukarka wyceny
Bambu Lab P1S - 0.4 nozzle
Proces wyceny
0.20mm Standard

Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.

Zapisane na tym urządzeniu.

Front License Plate Mount so you don't have to drill into your bumper. Fits 2025 XL/XLT/Lariat Ford Mavericks

Ocena
0 / 5
Polubienia
15
Pobrania
55
Wydruki
1
Wyświetlenia
622
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution

This is a License Plate mount I made because I refused to drill into the Bumper of my new car (and don't like how it looks when you put it in the windshield). So I made this. It clips around the lower Grill of some 2025 Ford Mavericks. It's been split in half to ease installation and fit on a Prusa MK4/MK4S Build Plate. The design is probably overbuilt, but it will likely last a long time and be significantly cheaper than one of the Universal metal designs on Amazon.

Maverick Grill Style

  • 4 Post Lower Grill on the 2025 Facelift Maverick

    • XL, XLT, Lariat

    • WILL NOT FIT THE LOBO OR TREMOR

  • Clamps around the 2 center posts on the lower grill

Required Materials

  • ~400g PETG (Or other heat-resistant filament)

  • 8x M5 Nuts

  • 8x M5x30 Bolts

  • 4x License Plate Bolts & Nuts

    • Crescent Wrench for Nuts because it's hard to access the back of the Mount.

Print Settings

  • 0.25mm STRUCTURAL

  • 4 Perimeters

  • 100% Infill (For Mounts)

  • 15% Cubic Infill (For Plate Body)

  • IF NOT USING THE PROVIDED PROJECT FILE, Flip the 2 mounts labeled "Flip" along the X axis

  • Pause Mount Prints at layer 88 to insert M5 Nuts

  • You may have to poke a hex key through the bolt holes a few times to clean off the bridging

Installation Instructions

  1. Install the Left half of the Plate Holder by holding the mount piece behind the body and loosely screwing in the M5 Bolts through the frame into the upper mount.

  2. Screw the remaining bolts into the lower mount, then tighten all of the bolts

  3. Install the Right half of the Plate Holder by lining up the Dovetail and loosely screwing in the M5 Bolts through the frame into the upper mount.

  4. Screw the remaining bolts into the lower mount, keeping the dovetail engaged.

  5. Install the License Plate (and frame if you have one) with one bolt at a time. It gets easier once the first one is in.

  6. Make sure everything is tight but not cracking the plastic. It will stiffen up significantly once the License Plate is screwed down.

Wear Testing

  • I will update this section if there's any issues with Fit, Finish, or Durability

  • INSTALLED ON AUGUST 12TH, 2025

  • Survived an automatic car wash!

  • I've noticed a very tiny bit of warping after a few months, but it's not affecting the strength or the fit. Maybe use a decently strong license plate frame just to keep everything straight and true.

  • Survived a 2500mi cross country trip with no issues!

Tagi