Leo's Leg Saver 3.0 - A dumbbell addon that saves your legs
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A dumbbell leg saver that saves your legs from getting bruised and banged up when setting up for e.g. bench presses.
- Ocena
- 0 / 5
- Polubienia
- 7
- Pobrania
- 36
- Wydruki
- 0
- Wyświetlenia
- 376
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Indoor Sports
- Licencja
- Creative Commons — Attribution — Noncommercial
A leg saver 3D printed endcap for good old castiron dumbbell/plate systems you might have at home which uses existing metal nuts for safety and magnets to attach the leg saver to the outermost plates tightly.
If you printed it/created it and thought it's cool and want to give a tip, I made a ko-fi page now after the suggestion of a friend. Though I expect absolutely nothing, so please don't feel urged to tip something! XD https://ko-fi.com/leostipjar
If you ever tried to set up for a dumbbell press and had your 30+kg dumbbells resting on your thighs just supported by sharp hex nuts and the ends of the bar, you might know why I made this.
I made this myself in Fusion360 and initially posted it on Reddit: https://www.reddit.com/r/homegym/comments/1n2wxe8/
Notes
Some notes about the leg saver that are 3D printing related:
- This was designed for MY dumbbell set I have at home - it's a typical 30/30mm set you can buy almost everywhere in central Europe and I suspect that they all have similar sizes. I made two insert version and for me the 16.5mm version would be perfect and the 18mm version works as well in a pinch. However: Do your own measurements and adjust the insert and outer plate holder to your own needs! See “How to adapt yourself” below.
- Note that it will NOT work for US 1 inch (25mm) systems - I don't have those, so you WILL need to change the design to your needs! ^^ See “How to adapt yourself” below.
- I designed it for my 5kg plates with a diameter of 19cm. I also made a design for 2kg and some 2.5kg plates with 14.5cm, but I have not printed it yet myself, as I don't need it for myself. Please also check your plate diameter to make sure it fits before printing! The insert and the outer plate holder are the same as for the bigger version so you can just use that.
- I printed this in Creality ST-PLA with a 0.8mm nozzle and 1.6mm wall thickness. The whole print on my old CR10s took around 13.5h and used about 350g of filament. I printed it with the logo side down and support for the middle.
- I drop-tested it multiple times with 35kg dumbbells onto a rubber tile from about 40-50cm height and different angles without any damage.
How to adapt yourself
I am providing also the Fusion360 archive as well as STL templates for the insert and the plate holder you can import in whatever CAD program you are using and cut yourself.I am providing also the Fusion360 archive as well as STL templates for the insert and the plate holder you can import in whatever CAD program you are using and cut yourself.
For the insert part (I sometimes also refer to it as “adapter”): Measure the height of your nut and subtract about 2mm from that: That is the depth you want the hole for the hex nut to be that you can cut either into the template or when adapting the parameters in the Fusion file. The hex nut should not stick out out of the outer plate holder! The outline of your hex nut you have to trace yourself unless mine fits (I used a piece of paper, traced my hex nut with a pencil and added a 10cm long reference marker to calibrate against in Fusion, then used the curves tool to create the outline of the nut). Add like 0.5mm-1mm of clearance.
Also cut a round hole through the entire part that is at least the diameter of your dumbbell handle threaded part (you can make it 31mm bigger when in doubt though and it should fit everything). See the inserts I made.
For the outer plate holder part: Simply measure the diameter of the usually round part of the nut that presses against the discs and add about 1mm of clearance (more clearance is important because the disc needs to tilt)
For the diameter: You can slightly adjust the diameter in the Fusion file with Fusion360 to fit your plates perfectly. My versions are 19cm and 14.5cm. I recommend choosing whatever is closer to your dumbbell diameter as a basis, since I made some adjustment in both files. My hope is that most 5kg plates are roughly the same though and that you don't have to touch it.
Hardware needed
- 12 disc neodym magnets 10mm diameter, 2mm thick. The whole for them is actually 3mm deep. You can them on amazon in like a 60 pack for ~10 EUR.
- 6 M3 screw inserts (also cheap on Amazon or Aliexpress) - I made 5mm holes for the inserts, as I found 4mm to be too thick and 5mm was perfect. If your inserts are ultra thin, that might be too wide though. I used a soldering iron tip to insert them, but you can likely also make a lighter and a screwdriver to work with it.
- If you don't want to use inserts you could also use M5 screws, tap the plastic and just drill the holes in the outer plate holder a bit wider.
- 6 M3 screws, somewhere between 5mm and 15mm length I would say.
- Again: If you don't want to use inserts you could also use M5 screws, tap the plastic and just drill the holes in the outer plate holder a bit wider.
Backstory and design decisions (copied over from Reddit)
After about 9 months of training and starting to hit higher weights for my DB benches, my thighs started to look all black and blue and bruised from the damage my starlock screw-on dumbbells left on them when setting up the press. I looked around to see if people came up with solutions for that, but only found more expensive handle options like Kensui's Adaptabells, which are cool, but I didn't exactly want new handles for 130 EUR and I didn't exactly trust the cheaper ones for 42 EUR to survive getting dropped at all after seeing a video of them shattering from basically nothing. Also I totally wanted to design something myself XD
So after a couple of iterations (which all worked kinda but had drawbacks), this is the version I printed today. I wanna go through some design considerations quickly for anyone wanting to make something like that as well (I might also just upload my STL files somewhere):
- 3D prints are cool but I wouldn't trust a 3D printed threads to withstand a 35kg (77 pound) or more, so I wanted to keep the iron nut but I also knew from experience that the print would be strong enough to withstand the impact itself.
- I did not really care for the depth it compensates as I have enough smaller plates to put on my dumbbell and have the 5kg plate be the last one on it. If you really need to bridge distance on the dumbbell without adding any plates you could always just print simple dummy plates (or cut and drill them from a piece of wood). Or use shorter DB handles or cut them off - because those kind of handles they sell here used literally in buckets for 2-5 EUR a piece.
- Version 1 had the nut screwed into the plate tightly and the plate border making contact on the outside of the plate. That had the downside that some plates had a height difference between the inside and outside surface and if the DB landed on the edge it would mean there was high sheer force on the thin plastic ring holding in the nut. I drop-tested it over 20 times from different angles and the ring showed stress marks, so I decided to change my approach completely and made a version 2.
- Version 2 had magnets on the side as the current version - the idea was (and still is) that the nut is enclosed in the leg saver but that the leg saver can move a bit. This means that the leg saver can compensate for the surface tolerances (the inner area is also 1mm recessed, just for good measure, but the inner area of a plate I found to be usually level or a bit recessed compared to the outside). In the same manner it can also compensate for a not perfectly tightened nut where the plates rock down on one side a bit more. The blunt impact onto the ground is now solely handled by the outer area of the db saver pressing against the outside of the plate. Again, this was successfully drop-tested from about 50cm (~19 inches onto my rubber mat) and this time found to work perfectly fine. However, I found that even with just my 30mm nuts (in Europe we do not have 1 inch (~25mm) dumb bell threads like the US but 30mm, which is a bit more, the shape and height of the nuts varied slightly depending on the vendor. Furthermore, due to the magnets it was a bit fiddly to remove the leg saver from the plate sometimes.
- Version 3 (which is the current version) thus kept the design idea, but added notches on the backside of the plate so you can slide a finger into it easily (see last pic, which also demonstrates the bit of play the leg saver has). It also introduced an intermediate adapter, which can just be changed to whatever starlock nut one has and then only this adapter has to be reprinted instead of the entire thing (that's the one that looks like a child's sand baking form XD). So the starlock nut goes into that adapter, the adapter into the leg saver and the adapter is then held in place by the plastic ring and 6 M3 screws. This also means that people from the US could now very likely also use the DB saver if somebody is making the adapter in the right size.
About the size: I made it to fit the 5kg plates I have here (the leg saver has a 19cm diameter) - it will only work with iron plates due to the magnets.
I also made a version for 2kg and some 2.5kg plates which is 14.5cm which uses the exact same adapter part, but I haven't printed it yet, since I currently don't really need it.
Cost-wise... this was about 350g of PLA+, which is currently around 15-20 EUR per kg, so think about 5-7 bucks in material, probably 1 EUR for electricity and probably 4 EUR for the magnets and hardware used. So roughly 11 bucks for one. You can use one on each dumbbell (because you put the DB onto your thighs with one side anyway), so you only need two for both dumbbells, which is about 22 EUR.
As I said, I might upload the STL files somewhere if multiple people express their interest in it (just don't sell them commercially XD).
So yeah, my thighs are safe now and I am happy enough thus far that I won't improve them for now I think. Just wanted to share it with you because I think there SHOULD be more option to use with the more affordable equipment. ^^After about 9 months of training and starting to hit higher weights for my DB benches, my thighs started to look all black and blue and bruised from the damage my starlock screw-on dumbbells left on them when setting up the press. I looked around to see if people came up with solutions for that, but only found more expensive handle options like Kensui's Adaptabells, which are cool, but I didn't exactly want new handles for 130 EUR and I didn't exactly trust the cheaper ones for 42 EUR to survive getting dropped at all after seeing a video of them shattering from basically nothing. Also I totally wanted to design something myself XD
So after a couple of iterations (which all worked kinda but had drawbacks), this is the version I printed today. I wanna go through some design considerations quickly for anyone wanting to make something like that as well (I might also just upload my STL files somewhere):
- 3D prints are cool but I wouldn't trust a 3D printed threads to withstand a 35kg (77 pound) or more, so I wanted to keep the iron nut but I also knew from experience that the print would be strong enough to withstand the impact itself.
- I did not really care for the depth it compensates as I have enough smaller plates to put on my dumbbell and have the 5kg plate be the last one on it. If you really need to bridge distance on the dumbbell without adding any plates you could always just print simple dummy plates (or cut and drill them from a piece of wood). Or use shorter DB handles or cut them off - because those kind of handles they sell here used literally in buckets for 2-5 EUR a piece.
- Version 1 had the nut screwed into the plate tightly and the plate border making contact on the outside of the plate. That had the downside that some plates had a height difference between the inside and outside surface and if the DB landed on the edge it would mean there was high sheer force on the thin plastic ring holding in the nut. I drop-tested it over 20 times from different angles and the ring showed stress marks, so I decided to change my approach completely and made a version 2.
- Version 2 had magnets on the side as the current version - the idea was (and still is) that the nut is enclosed in the leg saver but that the leg saver can move a bit. This means that the leg saver can compensate for the surface tolerances (the inner area is also 1mm recessed, just for good measure, but the inner area of a plate I found to be usually level or a bit recessed compared to the outside). In the same manner it can also compensate for a not perfectly tightened nut where the plates rock down on one side a bit more. The blunt impact onto the ground is now solely handled by the outer area of the db saver pressing against the outside of the plate. Again, this was successfully drop-tested from about 50cm (~19 inches onto my rubber mat) and this time found to work perfectly fine. However, I found that even with just my 30mm nuts (in Europe we do not have 1 inch (~25mm) dumb bell threads like the US but 30mm, which is a bit more, the shape and height of the nuts varied slightly depending on the vendor. Furthermore, due to the magnets it was a bit fiddly to remove the leg saver from the plate sometimes.
- Version 3 (which is the current version) thus kept the design idea, but added notches on the backside of the plate so you can slide a finger into it easily (see last pic, which also demonstrates the bit of play the leg saver has). It also introduced an intermediate adapter, which can just be changed to whatever starlock nut one has and then only this adapter has to be reprinted instead of the entire thing (that's the one that looks like a child's sand baking form XD). So the starlock nut goes into that adapter, the adapter into the leg saver and the adapter is then held in place by the plastic ring and 6 M3 screws. This also means that people from the US could now very likely also use the DB saver if somebody is making the adapter in the right size.
About the size: I made it to fit the 5kg plates I have here (the leg saver has a 19cm diameter) - it will only work with iron plates due to the magnets.
I also made a version for 2kg and some 2.5kg plates which is 14.5cm which uses the exact same adapter part, but I haven't printed it yet, since I currently don't really need it.
Cost-wise... this was about 350g of PLA+, which is currently around 15-20 EUR per kg, so think about 5-7 bucks in material, probably 1 EUR for electricity and probably 4 EUR for the magnets and hardware used. So roughly 11 bucks for one. You can use one on each dumbbell (because you put the DB onto your thighs with one side anyway), so you only need two for both dumbbells, which is about 22 EUR.
As I said, I might upload the STL files somewhere if multiple people express their interest in it (just don't sell them commercially XD).
So yeah, my thighs are safe now and I am happy enough thus far that I won't improve them for now I think. Just wanted to share it with you because I think there SHOULD be more option to use with the more affordable equipment. ^^
Regarding the license and commercial use
Commercial: I am okay if you print this for other people for the printing cost or a very small fee as this is meant to help people improve their home gym situation a little. I am however NOT okay if you just print his or have it mass-manufactured and then sell it yourself as a product. That kind of use is not allowed.
Attribution: Please at least link to here or the Reddit thread if you remix it or share it. ^^ Would be nice! :D
Remixing/Adjusting: Allowed. Please just don't make a copy, remove my name and claim it's yours and try to sell it as your product. Like… just use some common sense. XD