Kids Play Mixer Now with Bowl! - No Supports or Glue
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a printable representation of a kids play mixer I saw many years ago. No glue or supports are required.
- Ocena
- 0 / 5
- Polubienia
- 37
- Pobrania
- 54
- Wydruki
- 0
- Wyświetlenia
- 397
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution
This is a printable representation of a kids play mixer I saw many years ago. I tested each part and no supports are needed. However, depending on your printers overhang abilities; some parts may benefit from supports and noted in the print settings section.
The various parts connect or snap together in different ways to make assembly easier. The snap fits are tight and require a moderate amount of force. The pivot bar and screw were designed to have the ability to adjust tension on the mixer head. This way the mixer should be able to stay in the “up” position. Glue can be added to keep the screw in place.
I added two project files to aid in simplifying the printing. This way the print settings I used below are already configured. Some files need to have two identical parts printed and it has been noted in the file notes section. Also, I found adding an extra perimeter to the large parts helped with the top chamfer layer adhesion. The STEP files for each part are also included.
I was informed by my children that this needed a bowl. So I created a simple bowl that needs no supports. The file is called “Kids Mixer Bowl.3mf”.
Print Settings
- Base Back and Front = Supports are Optional, Standard 0.20 Balanced Settings
- Legs = Supports are Optional, I had to increase the wall thickness to 4 due to layer adhesion issues at the top of the chamfer, Standard 0.20 Balanced Settings
- Sides and Middle = Standard 0.20 Balanced Settings
- Pivot Bar and Screw, Stop Bars, Locking Pin = Infill Type to Gyroid at 20%, Standard 0.20 Balanced Settings
- Whisks = Add Brim, Infill Type to Gyroid at 15%, add infill modifier of 30% to top connector. This is to increase strength, Standard 0.20 Balanced Settings. If you are having issues with the print being knocked loose, typically this was around the 34% mark, I found increasing the nozzle temp by 10 degrees solves this.
- Bowl = Standard 0.20 Balanced Settings
Filaments Used
- Prusament PETG Signal White = Legs, Left and Right Side pieces, and Locking Pin
- Polymaker PETG Pink = Pivot Bar and Screw, Mixer Base Front, and the Middle piece
- Polymaker PETG Silver = Stop Bar x2, Whisk x2, Bowl
- Sunlu PETG Oak = Mixer Base Back
Assembly
- Step 1 - After printing all the parts assemble the two base pieces first, “Kids Mixer Base Back” and “Kids Mixer Base Front”. This is designed to not come apart after assembly. This is a tight fit and requires some force.
- Step 2 - Attach the "Kids Mixer Leg Left" to the base assembly from step 1. Next, attach the two stop bars to the left leg. Finally, attach the “Kids Mixer Leg Right” to the base assembly making sure the two stop bars are in the two locating holes before fully attaching. This is a tight fit and requires some force.
- Step 3 - Assemble the Mixer Head by attaching the “Kids Mixer Locking Pin” to the “Kids Mixer Side Left”. Next Place the “Kids Mixer Middle” piece on top of the left side piece. Finally, place the “Kids Mixer Side Right” on top of the middle piece.
- Step 4 - Take the “Kids Mixer Pivot Bar” and place it partially into the left leg. Take the Mixer Head from step 3 and guide in between the two legs. Once in place push the pivot bar through the Mixer Head assembly and the right leg. Finally, attach the “Kids Mixer Pivot Screw” to the pivot bar and adjust tension as needed.
- Step 5 - Attach the two whisks to the Mixer Head. The whisks were designed to be removable/replaceable.