1 / 9
Anycubic Kobra S1 spool holder with bearings // Kobra S1 kugelgelagerter Spulenhalter — zdjęcie 1
1 / 9

Anycubic Kobra S1 spool holder with bearings // Kobra S1 kugelgelagerter Spulenhalter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Spoolholder for the backside with bearings // kugelgelagerter Spulenhalter für die Rückseite

Ocena
0 / 5
Polubienia
20
Pobrania
126
Wydruki
0
Wyświetlenia
1423
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Because of the problem that the original kobra s1 backside spoolholder ist just a square part of metal without any support for moving the spool i was looking for an external spool holder which makes the movement of the spool easier. I've found a some interesting designs but nothing enough for me.

For me the most interesting design which also inspires me is from “faultedlogic” and can be found here for example:
https://www.printables.com/model/1336673-improved-spool-holder-for-anycubic-kobra-s1-3d-pri

He has also an interesting adapter kit:
https://www.printables.com/model/515029-improved-universal-spool-adapter-for-fdm-printers

But for me it was clear that i want a holder with bearings for the backside so the spool can run as smooth as possible. The holder should also suites to nearly every 1kg spool.

So i designed my own spoolholder from the scratch.

1 adapter plate Kobra S1 part 1 - bottom v1 → this plate matches the small recess on the backside of the Kobra S1 where the original spool holder should be mounted
2 adapter plate Kobra S1 part 2 - top v1 → this part will be mounted on the bottom plate and is necessary for the other parts. It has a m20 thread matching the shaft.
3 shaft for spoolholder - 7,99mm v1 → this shaft has an m20 thread for the mounting on the top plate. This shaft will hold the spoolholder. It has a diameter of 7,99mm and the bearing has a diameter of 8mm. The spaft is thick enough to go through the bearings and fix the inner rings of the bearings. So the bearings on this shaft (in the spoolholder) could work like they should.
4 spoolholder v1 → this spoolholder has two openings to match 608Z bearings at both sides. The diameter of the spool is 40mm and it has a m40 thread around. The end of this holder is conic from 90mm to 40mm so it should match for nearly every 1kg spool of filament.
5 conic nut spoolholder v1 → this nut will be mounted on the end of the spoolholder. It has a m40 thread and is also conic from 90mm to 40mm.

My printing setup:

spoolholder and conic nut → PLA, 15% infill, 0.2 layer
adapter plate part 1+2 → PETG, 50% infill, 0.2 layer
shaft for spoolholder → PETG, 100% infill, 0.2 layer

You also need:
2x 608Z bearings
2x M3x10mm screws

I've used PETG and the different infills for the shaft and the plate to make sure, that the design is stable enough. The shaft is only 7.99m thick and must hold a 1kg spool only with one side fixed on the plate. So the risk that the shaft will break is high if use other or less material. But to be honest i didn't test it with other material or infill settings - this way it works for me without giving me the feeling that the shaft will break.

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

Aufgrund des Problems, dass der originale Spulenhalter für die Rückseite des Kobra S1 nur ein eckiges Stück Metal ist, welches die Drehbewegung der Spule nicht wirklich unterstützt sondern eher zum Verhaken neigt, war ich auf der Suche nach einem Spulenhalter, der die Drehung der Spulen etwas geschmeidiger macht. Ich habe aber nichts 100% passendes für mich gefunden.

Das interessanteste Design, das ich gefunden habe, und das mich auch für mein Design inspiriert hat, ist von "faultedlogic” und kann bspw. hier gefunden werden:
https://www.printables.com/model/1336673-improved-spool-holder-for-anycubic-kobra-s1-3d-pri

Er hat auch ein passendes Adapter-Kit dafür:
https://www.printables.com/model/515029-improved-universal-spool-adapter-for-fdm-printers

Für mich war jedoch klar, dass ich ein Spulenhalter für die Rückseite des S1 haben will, der kugelgelagert ist, um die Bewegung der Spule so einfach wie möglich zu machen, und der für nahezu alle 1kg Spulen passt.

Also habe ich meinen Spulenhalter von Grund auf selbst designt:

1 adapter plate Kobra S1 part 1 - bottom v1 → Teil 1 des Halters zur Montage am originalen Befestigungspunkts des S1 Spulenhalters. Passt bündig in die entsprechende Aussparung auf der Rückseite.
2 adapter plate Kobra S1 part 2 - top v1 → dieses Teil wird auf Teil 1 montiert und ist für die weiteren Teile nötig. Es hat eine M20 Gewindeaufnahme passend zur Achse des Spulenhalters.
3 shaft for spoolholder - 7,99mm v1 → Diese Achse hat ein M20 Gewinde zur Montage auf der Adapterplatte. Die Achse ist 7,99mm dick, die Kugellager haben einen Durchmesser des Innenrings von 8,00mm. Die Achse passt so recht geschmeidig durch die inneren Ringe der beiden Kugellager, sitzt aber fest genug, dass die inneren Ringe festsitzen und sich der Spulenhalter nur über die äußeren Ringe der Kugellager dreht. Die Kugellager können so also arbeiteten, wie sie sollen.
4 spoolholder v1 → der Spulenhalter hat an beiden Enden entsprechende Vertiefungen, um die 608Z Kugellager einzusetzen. Der Durchmesser der Spule ist 40mm und die Spule hat ein M40 Gewinde rundherum. Das Ende der Spule hat einen Durchmesser von 90mm und läuft konisch auf die 40mm zusammen. Mit diesem Design sollte der Spulenhalter für die Durchmesser der gängigsten 1kg Spulen passen.
5 conic nut spoolholder v1 → diese “Nuss” wird auf das andere Ende des Spulenhalters geschraubt. Die Nuss ist ebenfalls konisch mit einem Durchmesser von 90mm auf 40mm laufend.

Meine Druckeinstellungen:

spoolholder und conic nut → PLA, 15% infill, 0.2 layer
adapter plate part 1+2 → PETG, 50% infill, 0.2 layer
shaft for spoolholder → PETG, 100% infill, 0.2 layer

Benötigt werden ebenfalls:
2x 608Z Kugellager
2x M3x10mm Schrauben

Ich habe PETG und mehr Infill bei der Achse und den Adapterplatten genutzt, um die Stabilität sicherzustellen. Die Achse ist nur 7,99mm dick und muss eine 1kg Spule halten, wobei sie nur an einem Ende an der Adapterplatte montiert ist. Das Risiko das der Schaft bricht, ist also recht hoch. Ich muss aber gestehen, dass ich die Teile bisher nicht in bspw. PLA und/oder mit weniger Infill probiert habe. Meine gedruckten Teile halten mit den genannten Einstellungen und ich habe nicht das Gefühl, dass die Achse bald bricht.

Tagi