BigTreeTech HDMI5 V1.2 Case for the Sovol SV08 - Stock Mount + Open Enclosure Compatible
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
SV08 mount for the BigTreeTech HDMI5 V1.2. Utilizes the stock mounting holes and works with the official enclosure.
- Ocena
- 0 / 5
- Polubienia
- 14
- Pobrania
- 57
- Wydruki
- 0
- Wyświetlenia
- 315
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
I have seen quite a few mounts for the HDMI5 from BigTreeTech designed for the Sovol SV08, however, most of the ones I have tried would prevent me from opening or closing the doors for my official Open Enclosure, or hung well below the base of the printer.
I was able to accomplish a few goals with my version:
- Maintained compatibility with the SV08 Open Enclosure, and avoided having the display fall below the bottom of the printer base.
- Utilized a pressure fit with the stock mounting holes, and passthrough to the inside of the enclosure
- Made it simple as possible to print and assemble
- Added the option to not use heat set inserts if that is not your jam or you don't have any on hand
- Designed it to match the stock display, as I found it quite good looking, and wanted my new display to follow the same design language.
Parts Required:
- BigTreeTech HDMI5 V1.2: https://a.co/d/iyzWzpM
- Ensure that you are getting the V1.2 version, V1.0/V1.1 will not work.
- Flat 90-degree HDMI Cable
- The one included with the HDMI5 is quite bulky unfortunately, and will not work with this design
- Be sure to check that the HDMI cable bends at the correct cable angle, it should bend towards the wider side of the connector
- I used this short extender plus a regular HDMI cable I had: https://a.co/d/4g1Qmqx
- 90-degree USB-C Cable
- This is the one I used: https://a.co/d/7Ud9e2P
- 4x M3x12mm Screws
- 4x M3x4x5mm (OD) Heat Set Inserts (Optional)
Filaments Used For Example:
Printing Tips:
I personally found success with a 0.2mm layer height, and tree supports with a 0.1mm distance. I also recommend tuning your elephants foot compensation for the display bezel if you have any issues with the fit, I tried to balance ample space with a firm fit so it didn't slide around.
If you use the heat set inserts, I recommend 4-5 walls on the cover, as this helps keep the insert solidly in place.
Assembly Instructions:
Assembly is overall pretty simple, I tried to reduce the parts and complexity as much as I could. I tested, and you are able to assemble the entire thing before slotting it into the holes on the base of the SV08. I find this to be the easiest method, as it's easier to screw in the cover this way, however, it may be easier to manage cabling by slotting in the base first, and then adding the display after. In that case, just use a M3 hex key.

Be careful not to over-tighten the screws, as this can put pressure on the front and back of the display, and potentially damage it or cause bright spots.
Regardless of whether or not you choose to use heat set inserts, please choose the model accordingly, as the hole sizes are different between each outer cover.

In order to mount it, just slot the pegs into the holes left behind when removing the stock display, and apply gentle pressure downwards, it should just slot into place and from my testing, holds quite strong just using a friction fit. The cables can then be routed through the hole in the base and SV08 base to the inside of the case.

This model was created as a part of a Makerthon hosted by @Aerocreative