Lymow One Lawn Striping Roller (V3.2)

This 3D model is a BETA Test, so use at your own risk and inspect it frequently for damage
but it allows you to mount a 1.5in x 12in Stainless Steel Conveyor Roller to your Lymow One or One Plus to add more defined lawn stripes to your yard as it mows.

Install and Demo: 

• V3.2 Update:

  • Lymow Roller Mount V3.2

    • Mounts have been modified and moved in closer to the center of the roller for better alignment to the bottom of the mower.

    • Also went back to the V1 design where the mount is angled inwards towards the front of the mower.

    • *** You may or may not need to cut off ~3/16 in. from each side of the main roller shaft depending on the spacing / tolerances between both mower tracks. A grinder with a cut-off wheel will make short work of this.

• V2.0 Update:

  • Lymow Roller Mount V2.0

    • All the same hardware and printing/instillation instructions as V1, arrow points towards the deck 

    • Redesigned to take advantage of the Lymow's weight by mounting perpendicular to ground instead of forcing the compliance of TPU to provide most downforce
      
       

• V1.2 Update:

  • Dampeners v1.2

    • Convex inter circle for a even tighter fit over 38mm rollers

    • * Soak in hot to boiling hot water for 2-3 minutes before installing 
      
       

• V1.1 Update:

  • Lymow Roller Mount v1.1 

    • Increased width from 12 to 14mm

    • Added a horizontal grove on the backside to induce a bending point

    • Added gussets and groves to increase strength along key areas 
       

  • Dampeners v1.1     

    • * Soak in hot to boiling hot water for 2-3 minutes before installing 

    • Increased width from 12 to 15mm for a wider surface area

    • Decreased diameter from 37 to 35.5mm for a tighter fit over 38mm Roller
      
       

• TPU 95A Print Settings:

  • 6 Perimeter walls

  • 7-8 Solid top & bottom layers

  • 100% infill

  • 0.4mm Nozzle
     

• M4 Stainless Steel Hardware needed:

  • 4x - M4 x 12mm screws (Mount to Lymow)

  • 2x - M4 x 16mm screws (Mount to Roller)

  • 6x - M4 Washers

  • 2x - M4 Nuts
    or

  • M4 Stainless Steel Button Head Hex Socket Cap Screw Kit: https://www.amazon.com/dp/B0DCVVNMQP
     

• Conveyor Roller Specs:

  • Size- 1.5"x11.8

  • Shaft Diameter- 12mm/0.47in

  • Roller Diameter- 38mm/1.5in

  • Roller Length- 300mm/11.81in

  • Total Length- 340mm/13.39in
     

• Optional Conveyor Roller Links: 

  • * Most of these links are/were prime shipping so you might have to do a little looking to get the best deal.

  • https://www.amazon.com/dp/B0BKLDWND7

  • https://www.amazon.com/dp/B0FBKCT9V3
     

• Heat Shrink Dampener Alternative:

  • 40mm Heat Shrink Sleeve Tubing

  • https://www.amazon.com/dp/B07WVTK4LJ

  • https://www.amazon.com/dp/B0CMXV37QT

Disclaimer of Liability

By purchasing, installing, or using this roller add-on accessory, you acknowledge and agree to assume all risks and responsibilities associated with its use. This product is currently in a testing and beta phase. While it has been designed for strength and durability, unforeseen issues may occur under certain conditions.

You agree to inspect the accessory regularly and ensure it remains in safe working condition. The designer is not responsible for any damage, injury, or loss resulting from the installation, use, or misuse of this product.