Energy storage and delivery for my touring bike
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is my project for energy storage and delivery for my touring bike (not an e-bike).
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 139
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Ideas
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Deutsch:
https://www.printables.com/model/1448832-energiezentrale-tourenfahrrad
This is my energy storage and delivery project for my touring bike (not an e-bike). This solution makes it possible to navigate with my cell phone even during longer tours without using additional power sources. This solution has now proven itself over 3000 km without any problems.
When it rains, I close the lid. This protects the USB-ports but also makes them inaccessible. If it would rain all day, the cell phone battery could discharge prematurely.
Fortunately, this has never happened to me so far. Of course, there are nicer ways to spend a rainy day than cycling😁 In any case, when the cover is closed, the housing provides reliable protection even against heavy rain.
My starting point was Jens During's charging module called ‘Forumslader’
https://www.forumslader.de/aheadlader-v6/
The name “Aheadlader” is a reference to where this module is actually intended to be used, i.e. in the steering tube (ahead). At first I implemented it this way but for me the limited space and poor accessibility of the module in the ahead tube in the event of problems or battery maintenance/replacement were a clear disadvantage. I also found the capacity of the batteries too small for long trips where you don't always have access to 220V power.
So I developed a plan to put this excellent electronics module in a new housing with larger batteries at the end of my bike's top tube.

The big advantage is that you can remove the three batteries and store them somewhere ‘warm’ in winter and recharge them as needed.
You can also easily replace the batteries if necessary. You could even carry spare batteries.
This solution also gives you access to two USB ports.
The module has connections for:
1. Dynamo (my hub dynamo: SHIMANO Deore XT DH-T8000-3D)

2. Light
3. USB-sockets
4. A start button (the electronics are very efficient and switch off when the dynamo is not supplying power). The start button is convenient when the bike is not moving and you want to check something or connect it to the mobile app. When the dynamo generates voltage, the module of course will start automatically.
5. A status LED (included).

6. A temperature sensor (included)
7. Bluetooth. Works with an app (Forumslader) on your cell phone and provides a lot of data about the batteries and, with the help of the dynamo, also speeds and distance traveled.
The housing:
As you can see on the photos, the batteries also need copper contacts, which you have to cut out of 1.5 mm copper sheet. Either you manage to press them in so that they stick (precize dimensions) or you have to use glue.
Materials used:
1x Forumslader V6 (order without batteries!). I paid €85 for it in 2024.
https://www.forumslader.de/aheadlader-v6/
3x Contact springs for the batteries:
https://de.aliexpress.com/item/4001076387868.html?spm=a2g0o.order_list.order_list_main.143.78541802Qe2v0G&gatewayAdapt=glo2deu
1x Copper sheet:
https://de.aliexpress.com/item/1005001323500499.html?spm=a2g0o.order_list.order_list_main.128.78541802Qe2v0G&gatewayAdapt=glo2deu
oder: https://www.amazon.de/dp/B0CH9MVXNZ?ref=ppx_yo2ov_dt_b_fed_asin_title
3x Batteries (18650 Lithium):
https://de.aliexpress.com/item/32771532107.html?spm=a2g0o.order_list.order_list_main.133.78541802Qe2v0G&gatewayAdapt=glo2deu
2x USB-Sockets (with 4 wires!):
https://www.amazon.de/dp/B0CNC1VV9W?ref=ppx_yo2ov_dt_b_fed_asin_title
To charge today's smartphones, the two middle (data) contacts must be connected. Otherwise, Android will complain and the charging speed will be extremely slow.
This means that USB-sockets with 4 connection wires are required!
4x plug connection between module and dynamo/headlight:
https://www.amazon.de/dp/B0C6PDXT5H?ref=ppx_yo2ov_dt_b_fed_asin_title
Cable from module to dynamo and headlight:
https://www.amazon.de/dp/B08KRZFTRB?ref=ppx_yo2ov_dt_b_fed_asin_title
Paint protection film:
https://www.amazon.de/dp/B08KRZFTRB?ref=ppx_yo2ov_dt_b_fed_asin_title
Further:
- 1x flat head Allen screw M5x14

- 1x square nut M5
- I took the start pushbutton switch (2p, impulse) from my own collection. The diameter of the hole in the endplate may need to be adjusted to fit the pushbutton switch used.
Max. dimensions for the pushbutton switch: 14x14x9mm (HxWxD). If the depth exceeds 9 mm (including contacts and wires), the endplate cannot be inserted into the housing. - Various wires for cabling. The cabling is shown in the documentation on the ‘forumslader’s homepage. The necessary openings for the cabling are provided in the housing. The specified cable type connecting the module with the dynamo and headlight must be pulled snugly through the housing openings provided so that no water can enter. A lubricant may need to be used.
- The specified connectors (4x) are mounted between module and dynamo/headlight and serve to connect/disconnect the module. Heat-shrink tubing should be used.

I used SolidWorks CAD-software for my design:

I have attached STEP data of my design. If necessary, I could also provide ‘native’ SolidWorks data.
3D print data don't make much sense because my housing design only fits on my bike’s top tube, which has quite a unique shape. It took several prototypes to get it to fit. So you will have to adapt my housing design to your bike’s top tube. If this shape is relatively simple (e.g., without tapering), I could possibly take care of that.
When mounting the housing to the bicycle top tube, the retaining wings must be bent open. To prevent damage to the bicycle paintwork, I applied a transparent paint protection adhesive layer. Bending the wings requires some force, but the material can withstand this well without damage.
The contact springs (3x) are held in place by round spring holders. The contact springs are not attached and remain suspended between the negative battery terminal and the copper contact.
The positive battery contact points on the copper contacts are knocked out slightly with a pointed punch (3x). The punching area on the contact plate must be clamped/supported with openings for the punch so that the plate itself remains flat. Only a small protrusion should be created, which must make contact with the positive terminal of the battery.

3D printing data:

Housing:
Material: Filamentum CPE HG100 Extrafill
Nozzle: 0.6mm
Layer height: 0.3mm, 1st layer height: 0.2mm
Perimeters: 5
Infill 50% Cubic
Temperatures:
Bed: 1st layer 90°C, rest 85°C
Nozzle: 1st layer 270°C, rest 265°C
Supports: 11x paint-on-supports
Print time: approx. 6h


Paint-on-supports (1-11):
Removing the supports is a bit challenging, but with a little skill it can be done well.

Further 3D-printed parts required:
- Endplate. 0.6 mm nozzle. The copper contacts are pressed/glued in here. The wires must be soldered on the side. The exact position must match the recesses in the edges of the endplate. No material (solder) should protrude from the side. Correct with a file if necessary. The same applies to the copper contact plates that are attached to the housing. Here, the solder joint must match the opening of the cable channels behind it. A good flux is essential for this soldering work. For those who have no soldering experience, these soldering tasks can be quite a challenge.
- Top cover. 0.6 mm nozzle (print upright)
- Guides for contact springs (3x). 0.4 mm nozzle. The inside is conical -> position correctly on the build plate!
- Temperature sensor holder. 0.25 mm nozzle
These parts have no supports.