TRX4M Land Cruiser LC80 Body Magnetic Mounts
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
I made trx4m mounts for my fms fcx18 lc80 body. it requires no permanent modification to the body.
- Ocena
- 0 / 5
- Polubienia
- 13
- Pobrania
- 46
- Wydruki
- 0
- Wyświetlenia
- 1109
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Share Alike
LC80 Body Mount for TRX-4M Bronco / Defender
Compatible with: TRX-4M Bronco / Defender
Tested with: Injora Universal LCG Frame (no K10 extenders)
Disclosure no AI was used to make the model or design, but I used chat gpt to format my description.
🧩 Overview
This mount lets you fit an FMS LC80 body onto your TRX-4M chassis.
It uses magnets for clean, tool-free attachment and fits directly on the Injora LCG frame it might also work on the default bronco or defender. Personally I used PETG for the body mounts. Its a good mix of flexible and strong for these parts.
There are 4 printed parts total:
2 × Bumper Mounts (front + rear)
2 × Body Magnet Aligners (front + rear)
🧲 Magnets
You’ll need 8 × 2mm × 6mm neodymium magnets.
Each part has holes for press-fitting magnets.
Magnets should sit flush or slightly proud of the surface.
The front bumper has two deeper magnet holes — ensure the magnets sit flat.
On my prints, the bumper magnets fit tight enough without glue.
The body alignment magnets require CA (super glue) to hold securely.
✅ Check magnet polarity before gluing!
🔧 Mounting Instructions
1 Install Bumper Mounts
Mount the front and rear bumper brackets using the stock TRX-4M screws (M2 × 8mm hex screws).
The FMS bumpers fit by friction. You may need to lightly sand for a snug fit.
They should hold firmly without fasteners. I have added holes for screws to go through the mount into the bumper. I used m2 x 6. you can go longer but you will need to drill it further or all the way through. I did not model it that way because it makes it almost impossible to get the slots to print well.
2 Attach Front Body Aligner
The part is not symmetrical — the slots are closer to the bottom.
The lower end should point downward.
Align the piece so it ends flush with the bottom edge of the LC80 body.
On my setup, this part friction-fit perfectly without glue.
3 Attach Rear Body Aligner
Use 4 screws to install this part on the rear of the LC80 body.
FMS does not provide a labeled exploded view, but this is what worked for me:
M2 × 10mm screws → bottom ladder holes
M2 × 8mm screws → spare tire mount holes
These screws go up through the bottom of the rear ladder and wheel mount area.
🛞 Optional: Rim Finishing Guide
The included rims can look amazing with some post-processing.
Print Settings
Material: ASA
Layer height: 0.08mm
Printer: Bambu X1C
Polishing Process
Mount a rim to the included polishing stand-off using an M2.5 × 10mm (or shorter) screw.
Place the assembly in a drill or rotary tool.
Sand progressively with:
220 grit
320 grit
600 grit
800 grit
Sanding wool
Smooth with acetone vapor or a light acetone wipe.
Finish with Gundam Marker Chrome (XGM100) for a mirror look.
⚙ Notes
Double-check magnet polarity before gluing.
Test-fit all parts before painting or final assembly.
Designed for Injora Universal LCG Frame without K10 extenders.
May fit others with minor adjustment.LC80 Body Mount for TRX-4M Bronco / Defender
Compatible with: TRX-4M Bronco / Defender
Tested with: Injora Universal LCG Frame (no K10 extenders)