Filament Dry Box – 4 Spool, Airtight, Silica Gel & Honeycomb Sample Labels
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
In this project, I tried to improve existing designs and combine their advantages into one practical, easy-to-use system
- Ocena
- 0 / 5
- Polubienia
- 23
- Pobrania
- 44
- Wydruki
- 0
- Wyświetlenia
- 642
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Share Alike
Update – 2025-12-04
A new Filament Sample Label System has been added to the model.
This includes:
Filament Sample Tags (Filament Sample with Honeycomb)
Honeycomb Sample Holder Panel
The new system allows quick identification of installed filaments and easy swapping of sample tags during filament changes. Unused samples can be stored on the Honeycomb panel. Installation details and new printed parts are included below.
Description
Most common filament dry box designs have their own pros and cons, and none of them fully met my needs.
In this project, I tried to improve existing designs and combine their advantages into one practical, easy-to-use system.
This is a 4-spool filament dry box designed to fit inside an airtight 14-liter food container (35 × 25 × 35 cm). The filament outlets are based on G1/4 pneumatic fittings, optimized so that the PTFE tube can slide fully into the housing, reducing friction almost to zero—unlike many other designs.
Each box uses 8 pneumatic fittings—two for each filament spool. This allows you to lock the PTFE tube on an unused spool, keeping the box fully airtight without needing to open the container every time you switch filament.
The rear side contains two dedicated silica gel compartments to maintain stable low humidity inside the chamber.
A Xiaomi Temperature & Humidity Sensor is also included for real-time monitoring.
The width of the roller system is fully adjustable. Since spool dimensions vary slightly between filament brands, each spool holder can be fine-tuned using M8 threaded rods and nuts before and after each roller.
Filament Sample Label System (2025-12-04 Update)
A modular, printable system for managing filament samples:
Filament Sample Tags
Printed using the same filament as your spool → accurate color identification.
Holds the filament name and color chip.
Easily swapped whenever you change filament.
Honeycomb Sample Holder Panel
Stores all unused filament sample tags.
Can be mounted on the dry box or a wall using super glue.
Modular design → print more panels for extra storage.
Print Instructions / Parts List
Non-Printed Parts
1× Airtight food container, 14-liter (35 × 25 × 35 cm)
8× Pneumatic fittings G1/4
(commonly used in household water filtration systems – easy to source)
16× Ball bearings 608 (8×22×7 mm)
4× PTFE tubes, 40 cm each (ID 4 mm, OD 6 mm)
1× Xiaomi Smart Temperature & Humidity Sensors
(Mi Temperature & Humidity Monitor 2 or Xiaomi Smart Temp & Humidity Sensor)
2× M8 threaded rods, 30 cm length
20× M8 nuts
Silica gel
(You can reuse silica gel packs from filament packaging. Recommended humidity is below 35%. If humidity does not drop, regenerate the silica gel and reuse.)
Printed Parts
2× Filament Spool Holder – Middle
2× Filament Spool Holder – Side
1× Silica Gel Box – No.1
1× Silica Gel Box – No.1 Door
1× Silica Gel Box – No.2
1× Silica Gel Box – No.2 Door
New Printed Parts (2025-12-04 Update)
Filament Sample Tags (as many as needed)
Honeycomb Sample Holder Panels (print based on desired capacity)
Assembly Instructions
Drill eight 16 mm holes in the container (refer to photos). (If nuts for the fittings aren’t available, you may print them.)
Install all G1/4 pneumatic fittings.
Assemble spool holders using M8 threaded rods, 608 bearings, and the printed side/middle holders.
Adjust roller spacing using M8 nuts for different filament spool widths.
Install silica gel boxes and fill them with silica gel.
Place Xiaomi humidity sensors inside for monitoring.
Insert PTFE tubes fully into pneumatic fittings → minimal friction path.
Print Filament Sample Tags for each filament type/color.
Print one or more Honeycomb Sample Holder Panels.
Mount the Honeycomb panel on the dry box or wall using super glue.
Insert the correct sample tag into the label slot when changing filament.
Store unused samples on any free Honeycomb slot.
Suggested Print Setup:
Nozzle: 0.4 mm (recommended: 0.2 mm)
Infill: 15% or more
Supports: Auto
Material: PLA