1 / 3
Cat & Dog Flap / Door for metal door — zdjęcie 1
1 / 3

Cat & Dog Flap / Door for metal door

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This pet door model is designed for cats and small dogs with a 190 mm x 190 mm clear doorway opening.

Ocena
5 / 5
Polubienia
3
Pobrania
32
Wydruki
1
Wyświetlenia
166
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

This pet door model is designed for cats and small dogs with a 190 mm x 190 mm clear doorway opening. The design allows for a wide opening suitable for small dogs.

 

📐 Project Specifications

 

Feature

Value

Doorway Opening (Clearance)

190 mm x 190 mm

Maximum Wall/Door Material Thickness

2 mm

Hole Cutout Size (in door/wall)

210 mm x 210 mm

Recommended Print Material

PETG (for durability)

 

🔩 Required Materials

 

Component

Specification

Quantity

Notes

Hinge Pins

4mm x 12mm Dowel Pins

2

An M4 screw (headless) can be used as a replacement.

Threaded Inserts

M3 Heat Inserts

12

Used in the outside frame part.

Screws

M3 Socket Head Cap Screws (SHCS)

12

Minimum length of 16 mm.

Tape

Foam Tape 1mm tick, 5mm wide

about 80cm long

For an air-tight seal.

Shims/Washers

Flat Washers or Shims M4 1mm tick

2

 

Magnets (Optional)

N52 Magnets 6mm x 3mm

2

also work with smaller magnets

Adhesive (Optional)

Super Glue (CA)

Small bottle

For securing the magnets.

Adhesive

3D Printing Bed Glue

As needed

For adhering the jig to the print bed.

 

Step-by-Step Assembly Instructions

1. Part Preparation

  1. Print the Parts: Print all necessary components, with PETG recommended for best durability.

  2. Jig (if used): Apply glue to the print bed to secure the jig during printing.

  3. Install Threaded Inserts: Insert the 12 M3 heat inserts into the screw holes on the outermost face of the Outside Frame Part. These are the holes that normally pass all the way through.

  4. Clear Inner Holes: The Inside Frame Part uses a beveled design without completely clear screw holes. Use a hex key to gently clear the material from the screw holes to prepare them for mounting.

  5. Install the Flap Magnet (Optional): Insert the magnet into the designated pockets on the pet Flap. Apply a drop of Super Glue (CA) to lock it in place.

  6. Install the Frame Magnet (Optional): Insert the magnet into the designated pockets on the pet Frame (inside or Ouside). Apply a drop of Super Glue (CA) to lock it in place.

  7. Install Hinge Pins: Insert the 2 x  dowel pins into the square holes on the sides of the Flap.

2. Door Modification

  1. Mark the Cutout: Mark a square cutout on your door or wall material. You can use the provided jig.

  2. Cut the Hole: Carefully cut a 210mm x 210mm hole. This is critical for a proper fit.

  3. Verify: Double-check the hole dimensions and ensure the corners are square (90 degrees).

 

3. Frame and Flap Installation

  1. Preliminary Frame Assembly: Align the Inside Frame Part and Outside Frame Part on either side of the door hole, clamping the door material between them. Secure the two bottom-most screws to hold the frame pieces together, but do not fully tighten them yet.

  2. Install Flap and Shims: Place a 4mm x 1mm shim or washer around each of the two hinge pins extending from the flap.

  3. Carefully insert the Flap into its final position in the frame, ensuring the two shims do not fall out during placement.

  4. Secure the Flap: Insert and tighten the two top screws of the frame to lock the flap into place and maintain proper hinge alignment.

  5. Final Frame Tightening: Insert the remaining screws and fully tighten all screws to securely clamp the frame to the door/wall.

 

4. Weather Seal

  1. Frame Sealing: Apply the foam tape overlapping the Inside and Outside Frame Part along the left, right, and bottom edges where the flap will rest.

  2. Flap Sealing: Apply the remaining foam tape to the top edge of the Flap (or the corresponding top edge of the frame) to complete the air-tight seal.

Tagi