1 / 3
Gehäuseboden für Advatek PixLite 16 Mk2 — zdjęcie 1
1 / 3

Gehäuseboden für Advatek PixLite 16 Mk2

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Stabiler Gehäuseboden für den Advatek PixLite 16 Mk2 LED-Controller.

Ocena
0 / 5
Polubienia
1
Pobrania
15
Wydruki
0
Wyświetlenia
49
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

Stabiler Gehäuseboden für den Advatek PixLite 16 Mk2 LED-Controller.
Die Platine wird auf integrierten Standoffs mit M3-Einschmelzgewinden montiert. Rund um die Platine sind 3 mm Luft, außerdem sind passende Ausschnitte für Stromzuführung und Netzwerk vorgesehen. Zwei zusätzliche Stützen ohne Schraubloch stabilisieren die Platine auf der rechten Seite. Ideal als Basis für ein geschlossenes Gehäuse oder den Einbau in einen Schaltschrank.

Merkmale

Passend für Advatek PixLite 16 Mk2 (200 × 120 mm Platine)

Rundum 3 mm Abstand zwischen Platine und Innenwand

Integrierte Standoffs für M3-Einschmelzgewinde (Heat-Set Inserts)

Zusätzlich 2 Stützen ohne Loch als reine Auflage / Support

Ausschnitte für Stromanschlüsse und Ethernet nach Original-Layout

4 Montage-Ohren zum Verschrauben des Bodens auf einer Platte oder Wand

Vollparametrisches SCAD-Design – kann bei Bedarf angepasst/remixt werden

Spezifikationen (Modell)

Geeignete Platine: Advatek PixLite 16 Mk2, 200 mm (L) × 120 mm (B)

Wandstärke: 3 mm

Bodendicke: 3 mm

Abstand Platine zur Innenwand: 3 mm

Standoff-Typ:

Lochdurchmesser für Heat-Set Inserts M3: 4,3 mm

Durchmesser oben (an der Platine): 10 mm

Durchmesser unten (am Boden, „Trompetenform“): 13 mm

Standoffs exakt nach gemessenen Lochpositionen der Platine ausgerichtet

Zwei zusätzliche Stützen rechts nur als Auflager (ohne Schraubloch)

(Exakte Außenmaße hängen von den Montage-Ohren ab und können in der SCAD-Datei angepasst werden.)

Empfohlene Druckeinstellungen

Technologie: FDM

Material-Empfehlung:

PETG oder ASA/ABS für den Außeneinsatz

PLA nur für Indoor / Testaufbauten

Schichthöhe: 0,2 mm

Infill: 20–30 % (Grid/Gyroid)

Wände/Perimeter: mindestens 3 Linien (≈ 1,2 mm)

Top-/Bottom-Layer: 4–5 Schichten

Supports:

Normalerweise keine Stützstruktur erforderlich, wenn der Boden flach aufliegt

Falls dein Drucker Probleme mit den Kabelausschnitten hat, dort „Support nur von Platte“ aktivieren

Druckausrichtung:

Boden flach auf dem Druckbett

Benötigte Hardware

4 × M3-Einschmelzgewinde (Heat-Set Inserts) für die Platinenmontage

4 × M3-Schrauben (Länge je nach Platinenstärke, z. B. 8–10 mm)

Optional: Holzschrauben / Blechschrauben zur Befestigung der Montage-Ohren am Untergrund

Hinweise

Vor dem endgültigen Aufbau zuerst einen Testdruck machen und Passung von Platine, Ausschnitten und Standoffs prüfen.

Wenn du eine andere Platine oder zusätzliche Kabeldurchführungen brauchst, kannst du die SCAD-Datei parametrieren/ändern und als Remix hochladen.

English – Model Description for MakerWorld

Title Suggestion:
Enclosure Base for Advatek PixLite 16 Mk2 (with Standoffs & Cable Cutouts)

Short Description
Sturdy enclosure base for the Advatek PixLite 16 Mk2 LED controller.
The PCB is mounted on integrated standoffs designed for M3 heat-set inserts. There is a 3 mm clearance around the board and dedicated cutouts for power wires and Ethernet. Two additional solid supports on the right side carry the PCB without screw holes. Perfect as a base for a closed housing or for mounting inside an electrical cabinet.

Features

Designed for Advatek PixLite 16 Mk2 (200 × 120 mm PCB)

3 mm clearance all around the PCB to the inner wall

Integrated standoffs for M3 heat-set inserts

Additional 2 supports without holes for extra mechanical stability

Cutouts for power connections and Ethernet according to the original layout

4 mounting ears to fix the base to a wall or backplate

Fully parametric SCAD design – easy to modify and remix

Specifications (Model)

Compatible PCB: Advatek PixLite 16 Mk2, 200 mm (L) × 120 mm (W)

Wall thickness: 3 mm

Floor thickness: 3 mm

Clearance between PCB and inner wall: 3 mm

Standoff type:

Hole diameter for M3 heat-set inserts: 4.3 mm

Top diameter (at PCB): 10 mm

Bottom diameter (at floor, „trumpet“ style): 13 mm

Standoff positions matched to the measured hole pattern of the PCB

Two extra right-side supports only as mechanical support (no screw hole)

(Exact outer dimensions depend on the mounting ears and can be tuned in the SCAD file.)

Recommended Print Settings

Technology: FDM

Material recommendation:

PETG or ASA/ABS for outdoor or harsher environments

PLA for indoor use / testing only

Layer height: 0.2 mm

Infill: 20–30 % (grid/gyroid)

Perimeters/walls: at least 3 lines (≈ 1.2 mm)

Top/Bottom layers: 4–5

Supports:

Usually no supports needed when printed flat on the floor

If your printer struggles with cable cutouts, enable “support from build plate only” for these areas

Print orientation:

Base flat on the print bed

Required Hardware

4 × M3 heat-set inserts for PCB mounting

4 × M3 screws (length depending on PCB thickness, e.g. 8–10 mm)

Optional: wood screws / sheet metal screws to fix the mounting ears to your panel or wall

Notes

Always do a test fit with your board and cables before final installation.

If you need to adapt the design for a different PCB or add more cable openings, simply edit the parametric SCAD file and upload it as a remix.