1 / 4
Prusa Core One Nozzle Wiper V2 with Purge Bin (left & right) — zdjęcie 1
1 / 4

Prusa Core One Nozzle Wiper V2 with Purge Bin (left & right)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Prusa CORE One Nozzle Wiper / Nozzle Brush / Cleaner, uses Bambu A1 silicone pad, custom G-code generator software

Ocena
4,965 / 5
Polubienia
1284
Pobrania
3137
Wydruki
144
Wyświetlenia
17 451
Oceny
141

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

This is a Nozzle Wiper Arm with Purge Bin for the Prusa CORE One /+ that uses Bambu Lab A1 silicone nozzle wiper pads. It's available for both left- and right-side mounting.

This is version 2, an iteration of the popular version 1, and based on the Core One Nozzle Wiper Remix V1.1 and the Core One Purge Bin Remix by Ed,  which are based on designs by PCR and nicohirsch, respectively.

Features

Version 2 offers several advantages over version 1 and other wiper arms. It's based on laser 3D scans of the CORE One to offer the best fit. One of the key advantages is that it places the silicone pad closer to the bed to allow the full pad to be used for wiping.

Feature

Version 1

Version 2

Precise dimensions and perfect fit based on 3D scans

✓

Left side Wiper Arm

✓

✓

Right side Wiper Arm

✓

Slim profile for unobstructed LED status bar visibility

✓

Full silicone pad accessible for nozzle wiping

✓

Wiping G-code generation with online nozzle wiping path generator

✓

Printable without supports

✓

✓

Heat-set insert mounting option (Voron or RatRig spec)

✓

✓

Hex nut mounting option

✓

✓

Square nut mounting option

✓

✓

Purge Bin with several magnet options

✓

✓

Customizable and remixable in Onshape, STEP files available

✓

✓

FAQ

  • Is this compatible with BIQU CryoGrip sheets?
    No. The lifting tab of the CryoGrip sheet occupies the same space that wiping arm needs to place the silicone pad close enough to the bed. You can find CryoGrip compatible remixes of V1 but they have the same limitations as V1.

  • Does automatic sheet detection work with the Wiper Arm installed?
    Yes, as of Jan. 26th, 2026, the right side wiper arms include a feature that allows enough nozzle travel for the printer to detect absence of a steel sheet.
    If you have printed an earlier version of the right wiper arm, it's recommended to reprint it if you need automatic sheet detection. The left wiper arm is not affected.

Wiper Arm

The Wiper Arm is available for left- and right-side installation, with multiple attachment options.

Silicone Pads

The Wiper Arm uses silicone pads for the Bambu Lab A1 printer. You can find them on the Bambu Lab store, Aliexpress, Amazon, and various other places under the terms "Bambu A1 nozzle brush" or "Silicone nozzle brush for A1", "Silicone nozzle wiper for A1", etc.

It should be 37mm long and 8mm deep and have 3 rows of 14 bristles. You don't need a genuine silicone pad, knock-offs will be fine as long as they look like in the image below.

I have sourced mine from the Aliexpress listing linked above.
Here are some sourcing links that the community have shared in their makes and comments:

Help out and share your own sourcing links in your makes. I'll keep this list up-to-date.

DIY: If you want to make your own silicone pad out of high-temperature gasket silicone, check out @Lucho's printable silicone brush mold.

Left and Right Versions

  • Left: If your door hinges are on the left (default), it keeps the right front corner of the bed clear, making it easier to lift the sheet.

  • Right: Shorter travel distance from parking position to the silicone pad.

Heat-Set Insert Attachment Option

Make sure to download the correct file for the heat-set insert type you have. Voron spec and RatRig spec inserts are supported, two very common insert formats.

Required Hardware

Qty

Description

Sourcing

1

M3 D5.0 L4.0 (Voron spec) or M3 D4.6 L4.0 (RatRig spec) brass heat-set insert

Aliexpress, CNC Kitchen, 3DJake

1

M3 x 8mm socket head or button head cap screw

Core One spare parts, Aliexpress

Square Nut Attachment Option

You should have a M3nS square nut in your spare parts bag or left over from your build.

Required Hardware

Qty

Description

Sourcing

1

M3 square nut thin (DIN 562 / Prusa M3nS)

Core One spare parts, Prusa, Aliexpress

1

M3 x 10mm socket head or button head cap screw

Core One spare parts, Aliexpress

Hex Nut Attachment Option

Required Hardware

Qty

Description

Sourcing

1

M3 hex nut (DIN 934 / Prusa M3n)

Core One spare parts, Aliexpress

1

M3 x 12mm socket head or button head cap screw

Core One spare parts, Aliexpress

Printing

The recommended method is to print the part with its front face facing down. The STL files are pre-rotated into the right orientation for printing in this orientation. 

Recommended Settings

You can go with the "0.2mm Structural" profile but I personally like to beef things up a little and use 4 perimeters.

Warping Risk

The part is long and skinny which makes it very prone to warping on the narrower side. It's highly recommended using a brim and possibly adhesives like Magigoo or similar if you choose to use a material that likes to warp.

If you experience issues with warping, you can also try @ImXotep's method and print the part standing on its "nose" with a large brim. It reduces the risk of warping due to the smaller bed contact area, but keep in mind that the holes for mounting hardware were not optimized for this orientation.

Material

Use a material that is suitable for the temperatures inside the enclosure. I used Prusament PC Blend and tested ASA as well.
Other materials with high temperature resistance: PC Blend CF, other PC, ASA, ABS, etc.
Some users have used PETG and report that it's working fine. Check out this Make by @Storbi81. 

CF and GF materials can help reduce warping.

Other settings:

  • Layer height: 0.2mm

  • Extrusion width: 0.45mm

  • Perimeters: 4

  • Infill: 15% Gyroid

  • Supports: No

  • Brim: Recommended

Installation

Step 0 - Warp Check

Inspect your part and ensure that it's not warped. Hold a ruler or other straight object against the font face of the Wiper Arm and verify that the edge is straight. If it's curved, reprint the part with a brim and/or printing adhesive. 

Step 1 - Insert Nuts

Install the heat-set insert, square nut, or hex nut in the printed part, depending on which attachment option you chose.

If you use one of the heat-set insert versions, make sure that the heat-set insert is installed deep enough so that the insert is flush with the plastic part or slightly deeper.

Step 2 - Attach Silicone Pad

Stick the A1 silicone pad onto the designated area on the printed part (see Adhesive section below). Roughing up the area can give the adhesive more grip and improve adhesion.
Pay attention to the rounded and sharp corners of the pad. Orient the pad so the rounded corners face towards the front. Stick it on as straight as possible.

Step 3 - Attach Wiper Arm

Move the bed to roughly 50mm Z-height via Control → Move Axis → Move Z on the LCD so that you have enough space underneath the bed to use a screwdriver.

Place the printed Wiper Arm onto the left or right arm of the bed frame and align it with the tab of the bed (the one with the fingerprint). Make sure the arm is straight and the silicone pad is parallel to the bed.
Then secure the arm with an M3 screw from the bottom. The correct screw length is specified in the "Attachment Options" sections above.
Tighten the screw fairly well to prevent the arm from moving.

Step 4 - Verify Installation

Make sure the arm is installed straight with no gap or almost no gap between the Wiper Arm and the PCB bed. If necessary, loosen the screw, correct the position, and tighten the screw again. Tighten the screw fairly well to prevent the arm from moving.

Adhesive for Silicone Pad

There isn't currently a definitive answer regarding the optimal adhesive for the silicone pad. Please experiment and share your results in the comments.

Here are my personal findings so far:

  • Factory Adhesive: I tested the pre-applied adhesive of the pads from Aliexpress. The bond failed and the pad detached from the PC Blend arm after only a couple of prints.

  • Silicone Adhesive: This video suggests using silicone adhesive to bond the pad. I suspect this likely only works if you first remove the factory adhesive from the pad, but I have not tested this myself.

  • 3M 300LSE Tape: I am currently using 3M 300LSE adhesive transfer tape applied on top of the silicone pad's factory adhesive and it's been holding like a champ for several months.
    It's a thin high-strength adhesive for low surface energy materials (such as many thermoplastics) and temperature resistant up to 148°C. Note that this tape will likely not stick directly to the silicone i.e. without the pad's factory adhesive intact. This tape is also not easy to source.

  • Differential Tape: During research I found that a differential tape with a silicone adhesive on one side and an acrylic adhesive on the other side would be ideal. Unfortunately, I haven't been able to source one.

You may also try superglue or two-part epoxy. Since silicone is notoriously difficult to bond to, I recommend applying your adhesive on top of the pad's pre-applied factory adhesive.

Community Recommendations

Below is a list of adhesives recommended by the community, with links to the respective makes and comments. Please help others and share what adhesive you used and how it's holding up.

Nozzle Wiping G-Code

Draw your own custom nozzle wiping sequence online with the new Core One Nozzle Wiper Path Generator tool that walks you step by step through creating your nozzle wiping G-code.

Replace the stock nozzle cleaning G-code.

  1. In PrusaSlicer, go to "Printer Settings" → "Custom G-code" → "Start G-code"

  2. Find the current nozzle cleaning command (G29 P9 X208 Y-2.5 W32 H4) and replace that line with the G-code you copied from the Wiper Path generator tool.

Always test the wiping sequence before including it in your printer profile. The tool provides standalone slowed-down test files to dry-run the sequence.

Purge Bin

The purge bin is completely optional and is not required for the function of the nozzle wiping.

Required Hardware

Qty

Description

Sourcing

2

Short M3 socket head cap screws (exact length is non-critical / approx. 6-12mm)

Spare parts, Aliexpress

Some

Neodymium block or disc magnets, strength doesn't matter (see Magnet Options below)

Magnet Options

You don't need to use all the magnet pockets in the printed part. Use as many as you like. The alignment of the bin is achieved by two SHCS screws, the magnets just prevent it from sliding around or rattling, and provide a nice snap feel.

There are several premade magnet options available:

  • up to 5 20x5x2mm block magnets

  • up to 5 20x6x2mm block magnets (Prusa spec)

  • up to 5 20x10x2mm block magnets

  • up to 10 6x2mm disc magnets

  • up to 8 8x2mm disc magnets

  • up to 5 10x2mm disc magnets

Customize in Onshape

If your magnet type is not available you can customize the Purge Bin magnets in Onshape and change the type, dimensions, rows, columns, and clearance in the Configurations panel in the upper left of the sidebar. 
To export, right-click on the part and select “Export”. In the Export dialog, select STL as the output format and set the units to millimeters.

Printing

Print the Purge Bin with the built-in "0.2mm Structural" profile in a material that can withstand the temperatures. Considering that it bears no load and isn't close to a heat source, PETG should be sufficient.

To fit the bin onto the Core One bed, rotate the part 35 degrees counter-clockwise.

Installation

Step 1 - Install Magnets

The magnet pockets have a 0.2mm diametric clearance, e.g. the pocket for a 6mm magnet is 6.2mm in diameter. This should result in a tight fit but it's not a press-fit installation. To prevent the magnets from falling out, apply a dot of superglue or epoxy adhesive into the pocket before inserting the magnet.

If you don't have magnets, that's cool too, as long as you install the alignment screws (see next step).

Step 2 - Install Alignment Screws

Insert two M3 socket head cap screws (SHCS) into the sheet metal at the bottom of the printer, as shown in the image below. These serve as alignment pins for the Purge Bin.

Step 3 - Install Purge Bin

Install the Purge Bin at the front on the bottom of the printer. Align the bin on both sides with the alignment screws that you installed in the previous step.

Testing

Before you continue printing, test the alignment of the Purge Bin and Wiper Arm to avoid collisions due to misalignment.

With the Wiper Arm and the Purge Bin installed, slowly lower the bed all the way to the bottom via Control → Move Axis → Move Z on the LCD and make sure the Wiper Arm doesn't collide with the Purge Bin.  There should be about 2mm clearance between the arm and the bin.

Remixing

All parts are available in STEP format. In the Design Resources folder you can find a full assembly of the Wiper Arm and Purge Bin with a dummy silicone pad in STEP format, as well as all the 3D scans used for this project in STL format.

You can also create a copy of the CAD to modify in Onshape:  
https://cad.onshape.com/documents/5b3897977821cb84aa960c8c/v/64cbd8e22447be60b0722af7/e/6e4dc12b048003864f109dd6

 

Updates

2026-02-01
  • Deprecated the "Thick Profile" Wiper Arms due to low usage to streamline choices and reduce maintenance overhead. The files remain available as a ZIP in the "Other files" section but will no longer receive fixes or updates.

2026-01-26
  • Added pocket for automatic sheet detection to right arms. As reported by @sherlook_3007371, the right arms were too thick and didn't allow for enough travel during the sheet detection routine for the printer to notice the absence of a print sheet. This is now fixed.

2026-01-07
  • Increased the base thickness of the Purge Bin to 3.2mm to improve bridging over the magnet pockets and have enough material above the magnets to prevent the magnets from shining though, resulting in better optics and reduced risk of print errors.

Tagi