Steam Diverter for Ninja Foodi Max 14-in-1 OL750
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Allows one to redirect steam from pressure release vent to selected direction. Rotates 360 degrees and even more.
- Ocena
- 5 / 5
- Polubienia
- 3
- Pobrania
- 9
- Wydruki
- 0
- Wyświetlenia
- 77
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Summary:
Didn't like steam going at high speed into my cupboards, couldn't find steam diverter that would work for Ninja Foodi Max 14-in-1 (OL750) so I created my own.
It is not very fancy, but does the job, and it rotates so you can divert steam in any direction you want (directing steam at yourself is not recommended).
Compatibility:
Ninja Foodi Max 14-in-1, OL750EU
Content:
Plate 1: v9 - newest version, extra thick (additional 1mm) compared to v8 or v7. Previous versions might get squishy for a moment during longer vents if printed in PETG, this should hold much better.
Plate 2: v8 - v7 but slightly tighter. v7 was a holding to valve even after months, but was slightly too lose to my taste.
Plate 3: v7 - used it for almost a year with occasional usage, works fine, but probably too thin for PETG that I used and while there was no significant deformation and rotation was working fine, it got slightly loose with time and didn't like longer vents.
Why would you select v7 or v8 over v9? To be honest, doubt there is good reason, at least not for OL750, but maybe you are printing it for some other model and it has less space around vent than OL750? Other reason might be that v9 is harder to put together, and maybe on your printer.
Recommended material:
v9: PETG, ABS, ASA, CPE, PA etc. (generally avoid PLA)
v7/v8: ABS, ASA, CPE (PETG kinda works, but see comments above)
Note: TPU might work for v9, but v7 is too thin and even harder TPUs (95A, 98A, 55D, 64D) might be too soft and not hold to vent (TPU has generally lower friction than anything listed above except of PA/Nylon).
Recommended slicing settings:
Walls: ALL (3mf is configured for 7, but generally you want this thing solid for thermal mass)
Seam:
Scarf joint seam: enabled, contour and hole (seams on Bambu P1S and X1C printers are generally bad quality, and would induce friction between parts, might not be needed on other printers)
Conditional scarf joint: enabled
Scarf length: 10 (default 20 didn't work well IIRC)
Wall generator: Arachne
Note for TPU - I didn't have great experience with TPU and scarf joint, typically it was stringy mess, but I was lazy and used default setting for TPU. At the same time seams I got with TPU were resulting in small blobs and strings that did affect parts fitting. Just saying - you are on your own here.
Assembly:
Print selected version
Push top into base.
v9 might require some slight cleanup (if you see strings) and quite a lot of force - even with PETG it is quite stiff at this thickness, so had to push it against some hard surface to get it in.
Put it on a vent. Regardless of version it should require very little force or no force at all. When in position it shouldn't get out when you try to just lift it (it should lift together with the vent).
Select your favorite diverter position. Done.
Disclaimer: Use at your own risk.
