1 / 1
Qidi Q2 120mm Exhaust Fan Upgrade and Custom Back Panel — zdjęcie 1

Qidi Q2 120mm Exhaust Fan Upgrade and Custom Back Panel

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This upgrades your exhaust to a 120mm fan and uses the old 80mm exhaust fan to cool the MCU board rather the 40mm fan.

Ocena
3,625 / 5
Polubienia
110
Pobrania
413
Wydruki
8
Wyświetlenia
4266
Oceny
8

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

UPDATES

12/26/25

  • Added a version of the back panel that doesn't have the PTFE tube cutout in the top right corner.

  • Added a printable TPU plug for the top right corner TPFE guide cutout.

  • Removed the unused holes to mount the Qidi box hub in the center of the back panel.

  • Added versions with holes to the top and bottom left sides to allow easy attachment of exhaust pipe adapters.

This will allow you to do the much needed upgrade on chamber exhaust fan. This will allow you to replace the stock 80mm fan with your standard size 120mm fan. The fan will need to be 24V or you will need to use a stepdown converter if you would like to use a 12V fan. When you upgrade the exhaust fan to a 120mm fan this design repurposes it as an upgraded MCU board cooling fan. The stock MCU board cooling fan on the back panel is a 4010 fan and the exhaust fan is an 8025 fan. This is a wonderful way to upgrade both the Exhaust fan and MCU board fan by only needing to purchases a single 120mm fan. 

The fan duct insert is actually what sticks out of the back panel for attaching a hose to vent fumes elsewhere. There is two different versions, one sticks out 10mm from the back panel and the other sticks out 20mm. The 20mm version will give you more space to clamp a host onto it and the shorter 10mm is better for those who don't use a hose to vent fumes.

PRINT SETTINGS

 

0.2mm Layer Height

Arcane Walls 

5 Walls

25% Honeycomb infill

 

FILAMENTS

 

I personally printed mine in High Speed PETG for the back panel and for the fan/filter housing. I have tested it during multiple 5-6 hour prints at 65C chamber temp with no signs of melting or warping yet. I would recommend printing the fan/filter housing out of ABS/ASA if you print at high chamber temps often just to be safe.

MATERIALS

1x 120mm fan 

When swapping the fans the parts have all been designed to use the stock screws so no extra hardware is needed.

When transferring parts from the stock back panel to this one the rubber guide for the PTFE can be tricky to remove. It simply just pushes out but there is a little bit of glue all around the edges. You may find it helpful to gently run a knife or razorblade along the edges to help loosen the glue.

The stock 80mm exhaust fan will be connected to the green 2 pin in this image and the stock board cooling fan will be connected at the white 2 pin next to it. Since we are getting rid of the old board cooling fan and replacing it with the 80mm fan you just simply swap the 80mm fan over to the white connector and remove the stock board fan entirely.

If your 120mm fan has a 2 pin connector you can use the same green 2 pin on the board. Please be sure to check that the connector on your fan to make sure it's the correct one needed. If your 120mm fan has a 4 pin connector you will use this empty port circled in the photo below. Once again make sure to look at the connector on your fan to insure that it is the correct one. Going from top to bottom the pins are Ground, 24V, PB12 (Tachometer/RPM), PWM control.

The stock MCU board cooling fan run at 100% power whenever the printer is on. Sense we moved the 80mm fan to cool the board it is much stronger and doesn't need to be at 100%. Using a temp gun the board was 60C with the stock fan at 100%. With the 80mm fan installed and only at 35% the board was 40C. With the 80mm fan only being at 35% it is actually quieter than the stock fan. To get the new 80mm fan to run at 35% power we need to make a small change in our printer.cfg. Open your pinter.cfg and scroll down until you find the [controller_fan board_fan] section. There you need to edit the second to last line from 1.0 to 0.35 or just copy this code below. Once you have made this change make sure to save and restart.

[controller_fan board_fan]
pin:PA9
max_power:1.0
shutdown_speed:1.0
cycle_time:0.01
fan_speed: 0.35 # <---- This is the number that is changed
stepper:stepper_z,stepper_z1

If you are using a 4 pin 120mm fan, sense we are using different pins on the board we need to make a small change to the g-code. Open your printer.cfg and scroll down until you see [fan_generic chambe_circulation_fan] The very first line you need to change the PIN to PA8 or you can just copy this code below. Once you have made this change make sure to save and restart.

[fan_generic chamber_circulation_fan]
pin: PA8 # <---- This is what was changed
shutdown_speed: 0.0
cycle_time: 0.0100
hardware_pwm: True
kick_start_time: 0.100
off_below: 0.0

That is all you need to do and once again if you have any questions or need any help please reach out to me.