Hybrid upgrade XY joiners for Rat Rig V-Core 3/3.1 printers
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
These XY joiners enable upgrading a V-Core 3/3.1 to CoreXY hybrid operation while retaining the stock belt offsets.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 23
- Wydruki
- 0
- Wyświetlenia
- 222
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Update: Now that I have had a chance to fully test my Full Metal XY joiners for the hybrid upgrade I prefer them to these ones. Testing shows that the lighter weight and extra rigidity provide surprisingly more gains in Input Shaper results than I expected. These are now also available from Funnssor. Unlike Rat Rig's hybrid upgrade XY joiners, both my options have the correct belt off-sets for all previous V-Core 3 and 3.1 print heads.
The files for the better all metal XY joiners and all other parts required for the hybrid upgrade can be found here: https://www.printables.com/model/1507704-hybrid-upgrade-xy-joiners-for-rat-rig-v-core-331
If you want to take your upgrade to the next level of print quality and speed, consider jumping straight to the the Full Frontal Gantry mod XY joiners.
These joiners are VERY SIMPLE to retrofit to any of the open front, OneBox or Rat Rig version of an enclosed Rat Rig V-core 3 or 3.1 printer. You need an enclosed printer for these XY joiners as you need to moves your Y linear rails to the top of the Y extrusions.
These XY joiners are fully compatible with al existing V-Core 3, 3.1, EVA, Microlight, compatible print heads.
These joiners use standard Rat Rig VC4 XY joiner top plates.
If your just doing the XY joiner upgrade the only custom metal parts required are the bottom XY joiner plates and the spacer tubes.
Coffee fund
I except no kick backs or royalties from third party companies such as Funssor who manufacture stuff I model and post on Printables.
If you decide to make a donation to my coffee fund (which keeps me up late at night doing more of this stuff) I would appreciate it. There is absolutely no obligation for you to do this. My PayPal account is [email protected]
Please remember to post feed back as it is always valuable to me for future iterations.
Many thanks.
Liam Venter
MFBS Design
Notes:
The bottom XY joiner plates are different from the VC4 bottom plates. This is required to get the necessary spacing for the two bottom cap screws that bolt into T nuts in the 2020 X gantry extrusion because the 2020 extrusion does not insert as far into the XY joiners on the VC3.1.
I have split the printed extrusion locators in the XY joiners into two parts in a different manner from the VC4 XY joiners. This makes thse parts eaiser to print flat on the bed without supports.
These XY joiners locate the X extrusion and bearings in the correct planes for the V-Core 3/3.1 which are different for the VC4. This means no other frame or print head upgrades or modifications are required to fit these XY joiners.
The countersunk bolts and cap head screws are different lengths from the original ones. I have given careful attention to the design to ensure that the length of all screws are readily available lengths.
Instructions
Assembly of everything is self evident.
When you print out the XY joiners measure and check the stack height of the two plastic parts. They should have the same stack height as the two long internal aluminium support tubes (43mm). Remember some materials like ABS will have some shrinkage when you print it and you may need to compensate fo this shrinkage in your slicer settings.
BOM
Please note the following BOM does not include the parts you will reuse from your VC3.
Funssor include everything you need as below in their VC3 hybrid upgrade kit , other than the longer shaft motors.
Top and bottom plates
2 x V-Core 4 top XY joiner plates.
2 x V Core 3 hybrid joiner lower plates
XY assembly hardware and spacers
All spacers for the XY joiner assemblies can be cut from a length of 10mm OD X 5mm ID aluminium tubing.
4 x 43 mm spacer 8mm OD/5 mm ID
2 x 29 mm spacer 8mm OD/5 mm ID
2 x 16 mm spacer 8mm OD/5 mm ID
2 x 13mm spacer 8mm OD/5 mm ID
Countersink screws and nylock nuts
8 x M5 x 55 x 0.8 countersink
2 x M5 x 28 x 0.8 countersink
8 x M5 X 0.8 Nylock nuts
Cap head screws
4 x M5 x 12 x 0.8 countersink
Bom for mounting X-stop bumper
2 x M3 x 4mm OD x 5mm long threaded inserts (OD and length not critical, use what you have).
1 x M3 x 16 socket head cap screws.
Atrtribution:
This hybrid upgrade is a derivative of the original Rat Rig VC3 and the VC4 printer.
Some parts of this upgrade are derivatives of the excellent design of the Rat Rig VC4 hybrid printer.
These two printers have different open source licenses, The VC4 has an Open Source Non Commercial license and the VC3 had a Open Source license, Hence parts of this upgrade inherit the VC3 license and are covered by the Commercial use license and parts of it inherit the VC4 Non Comercial license.
Updates
5th August 2024:
Corrected error in upper and lower right hand side XY joiner printed parts and strengthened upright tab on lower left printed part.
24th August 2024:
Corrected 0.4mm offset error, in the location of the 2020 extrusion tube, in the right hand joiner printer parts.
23/12/24
Added a X-stop bumper
Modified top left XY joiner printed part to mount X-stop bumper.
25/12/24
Corrected bottom left XY joiner STEP file (The STL file had the correct sizing for the 2020 extrusion but the STEP file was incorrect.