Solid and Compact F-Clamp Holder for Long and Heavy Clamps
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Wstępna wycena dla PETG
21,36 € – 26,11 € netto (bez VAT)
Dla pliku: LR2218 Clamp Holder_0.2mm_PETG_MK3S_1d0h57m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 23,74 € netto (środek widełek).
- Masa podana przez autora
- 291 g
- Czas druku podany przez autora
- 24,96 godz.
- Materiał u źródła
- PET
- Materiał wyceny
- PETG
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
A very solid F-clamp holder (bar clamp) for heavy and long clamps. (with Fusion360 design)
- Ocena
- 5 / 5
- Polubienia
- 168
- Pobrania
- 883
- Wydruki
- 6
- Wyświetlenia
- 3716
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Share Alike
I designed this f-clamp holder to store my clamps in the most compact way on the wall. The holder is intentional massive and bulky to withstand the weight and forces that are put on the object.
For regular and small clamps, have a look at design LR2219.
How to Print this Clamp Holder
There is a Prusa Slicer example project ending in “Print”, where I configured all my recommended settings. If you create your own project, please note the unusual print orientation! The object is printed upright, standing on the small bottom area.
While a print on the “back-side” is technically possible, the resulting holder will have the layers in the wrong orientation. Unless you use ASA for the print, the holder will most likely break over time.
Check out my recommendations in the table below:
| Nozzle Size: | 0.4mm |
| Layer Height: | 0.2mm |
| Filament Materials: | PETG or PLA |
| Perimeters: | Three perimeters for extra toughness |
| Infill: | 15% |
| Prusa Slicer Profile: | “0.2mm Quality” |
Dimensions
You find all dimensions in the drawing above. The holder will work up to a bar width of 8mm and a head width up to 25mm. The holder is designed for long clamps, where the bar will provide enough weight to hold them securely in place.
I did not test clamps with a head length of more than 20cm, so I do not know how well they will stay in place.
Montage
Use 5mm countersunk wood screws to fasten the holder on any wall. Ideally, put a screw in every prepared screw hole to equally balance the forces and avoid bending of the part.
Tighten the screws carefully by hand!
About the Fusion360 Design
The Fusion360 design lets you easily adjust the dimensions of the slots and the total size of the holder. The design does automatically adjust the number of slots, to make the best use of the width. Only adjust parameters in the favourites section.
As Fusion360 has numerous problems, especially with fully parametric designs, I only recommend adjusting the design in Fusion360 if you are an experienced user of this software.
Variants
- LR2218 Solid and Compact F-Clamp Holder for Long and Heavy Clamps
- LR2219 Compact F-Clamp Holder for Regular and Small Clamps
Explore More from Meti·kumi
Interested in my designs? Browse through my collection of 3D models:
👉 https://metikumi.com/3d-models/
Stay connected on social media for the latest updates and work-in-progress insights:
Conclusion
This is a long print, but it will allow you to store more clamps in a smaller space. 😃 Please rate and upload photos of your prints if you like this model, and let me know if you run into problems or have ideas on improving these models.
Happy printing! 😄