Linked Helix Premium Pack 1 (Kinetic DNA Spiral Toy/Art Piece)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a series of links that are interconnected to form a spiral when twisted. It prints in place and has 100+ sizes.
- Ocena
- 0 / 5
- Polubienia
- 5
- Wydruki
- 0
- Wyświetlenia
- 192
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Art & Designs
- Licencja
- Commercial Use
Introducing the Linked Helix!
This is a fully parametric design that prints flat on the build plate as a Print-in-Place design, but then with a twist elegantly spirals into a helix. It is made up of a series of links that all freely spin around a central axis, but the “twist” is that as each link turns, after it turns a certain amount, it turns the adjacent links along with it and so on in a cascading effect! This creates an elegant arch that can spin about freely and makes an impressive looking and fun fidget toy. It's also fairly durable! The amount of links and the length of the links can be changed in OpenSCAD to create a diverse ecosystem of helixes that look and feel different from each other, with there also being over 100 different pre-generated sizes to choose from! This is a collection of five different helix types, each with their own look and feel, and each customizable, resulting in a massive ecosystem of unique helixes! All helixes work off of the same base design, so all helixes have the same level of reliability and printability! There are also three different types of stands to fit your specific helix needs!
This pack contains the following 5 helixes!
The Rounded Rectangular-A more basic helix like the Rectangular helix, but the ends of the links are rounded for ultimate comfort in the hand and a different, more fancy, look!
The Jagged-A Helix where all the links have sharp turns for a stunning look that can't be found anywhere else!
The Rounded Jagged-It's just like the Jagged helix but with the ends rounded for a different look and better comfort in the hand!
The Half Circle-A Helix where all the links have curved downwards for a "bowl" like look that curves in on itself, turning the normal helix into something else entirely!(Large ones also look stunning when in motion)
The Full Circle-This helix is basically like the Half Circle helix but doubled, giving it an entirely new look and feel!(Personally I like the Half Circle helix better though)
As you can see in the pictures, some of these helixes also come in tree shapes! This is thanks to the Angled Link Length feature which makes each link slightly longer than the link that comes before it, creating sloped sides to the helix! These can feel and look entirely different from helixes without it, giving even more possibilities for the helixes! Did I mention you can even print one with a star on top of it to have a Linked Helix Christmas tree?
When you buy this pack you aren't buying a single model, you are buying a vast ecosystem with 1000s of unique combinations.


Do you like these helixes but aren't sure if your printer can handle them or if you'll like them? No problem! The Rectangular helix variation is available for free at the link below!
(But there's no angled link lengths and you can't add a star on top, not to mention that it's the most basic shape of them all) Don't miss out on this design's full potential! Buy the premium pack!
https://www.printables.com/model/1454939-linked-helix-fidget-kinetic-dna-spiral-toyart-piec
The Helix naming system and choosing your first helix
Here's your complete guide to picking your first helix! First off, explaining the naming system. Every file I provide will start with LH, standing for Linked Helix. This will go over the different sections in the file names and what they mean. Example values will be used.
_60Links_ All helixes, no matter the type or size, will have this in the file name. This is how many links are in the helix, or how long it is. Each Link is 3mm thick, so ten links will be 30mm long. Also, each link can rotate 12 degrees in either direction before pulling the next link along, meaning it takes about 15 links to do a full 180 Degree spiral.
_40mm_ This number tells you the length of the links in millimeters. This is the total distance from one end of the link to the other. Also, with a longer link length the spiral will appear more “compressed”, like the spiral is tighter, even if the rotation between the links is the same. It's just a neat trick of the eyes :) This helps give a lot more variety between helix types, so I encourage you to try printing multiple sizes and seeing which you like best! They feel a lot different to fidget with too. This doesn't apply to the HalfCircle and FullCircle helixes as they don't have link lengths.
_Slanted2mm_ This number tells you if the sides of a helix are angled, and by how much. How this works is that the number, in this case 2mm, is added on top of the link length and each link is 2mm longer than the previous one causing the links to get longer and longer. These helixes give a massively different experience than normal ones and look more tree shaped. I only provide a few sizes of these, all with a slant of 2mm, but you can make your own, and that's what makes the easily customizable parametric nature of this design so great! Note that as the HalfCircle and FullCircle helixes don't have link lengths, this does not apply to them.
_+10EH_ If this is in the file name, that means the helix has Extended End Hubs! The Extended End Hubs is when the ends of the center of the helix stretches out a bit, giving you a handle or place to grab the helix. The number, 10 in this case, is how far in millimeters the end hubs stretch beyond where they would normally stop. The normal end hubs only stick out by about 3/4ths of a millimeter, not enough to grab onto.
_Star_ If this is in the file name, that means there's a star on one end of the helix! This is a simple feature, it literally just means there's a star on the helix. This is mainly a feature so you can make a Linked Helix Christmas tree with a nice star on top! This also disables the Extended End Hub on one end of the helix, making it so it only comes out of the other end if used.
_RoundedRectangular_ This will be at the end of every file name and simply tells you which of the 5 helix types it is! This example is, obviously, a RoundedRectangular helix type.
I chose to provide sizes only up to 60 Links and 80mm as I felt that was a good stopping point in general, but that's not to say you can't use the parametric OpenSCAD customizer to make one waaaaaay bigger, as long as your printer has a build plate that it can fit on. For your first helix, I recommend printing one that's between 20 and 30 Links, with a 40mm Link Length as I think that provides the best mix of playability and coolness without taking too much filament. And then, if you like the feel of it, you can go back and print a massive one.
Also, if there's a specific helix size you want(like one bigger than the provided sizes) ask in the comments and I might be willing to render it and upload it for you!
The Three Stands
There are three stand types: The Spinning Stand, the Bottom Clip Stand, and the Bottom Hub Grip Stand.
The Spinning Stand is a stand that goes around the helix and holds it by the little indents on the two ends, which also allows the helix to spin in the stand and adds a whole new dimension of play with it in the stand, as well as being a great way to display it. But. There are two downsides to this stand, namely that it takes more filament than the other two and that you have to print the correct size to go with a specific helix. For this stand you have to print the one that matches the number of links the helix has, and if there are Extended End Hubs on the helix it also requires a different size for those. Also, it is only compatible with helixes that have a link length of 80 or less. If a helix has a link length of more than 80, it will not fit. As a result, the Half Circle and Full Circle helixes won't fit unless they are very small sizes, and most helixes that make use of the Angled Link Length won't fit either, if the longer links exceed 80mm.
The Bottom Clip Stand is a stand that holds the helix by the bottom two links and nothing else. The advantages are it takes very little filament(only around 7 grams) and is compatible with ANY SIZE HELIX. The disadvantages are that it is a bit wobbly and less stable than the other two stands and it grips onto the bottom TWO links, keeping either of them from rotating. This means that while the rest of the links can turn freely, the bottom two links will not be able to rotate apart from each other. It's not a good stand for playing with the helix, but it works great for sitting it on a shelf somewhere as a display item. It also has a hole in it for an Extended End Hub of up to 10 mm to seat into, which would make it a lot more stable. An Extended End Hub value of more than 10mm will cause the bottom two links to not seat fully, but it will still stay in the stand just fine.
And finally, the Bottom Hub Grip Stand. This stand is a lot like the Bottom Clip Stand except it doesn't grab onto the bottom two links and lets them rotate freely, plus its a lot more stable. The downside is it will only work with helixes that have an Extended End Hub of 10mm or more. If it's less than ten, say 5mm for example, it will still work but it just won't be quite as stable. If it's more than ten, the helix will just be positioned farther up in the air instead of right above the stand. (I haven't provided many helixes with Extended End Hubs though)
Print settings and post-processing
Material: I used PLA, although any similar material like PETG should work fine as well.
0.4mm Nozzle, 0% infill, and 2 wall lines-the weakest part of the helix is the center of the links which prints solid even with just two wall lines, so there is next to no advantage to adding infill or doing more than 2 wall lines. The only part that gains any real strength is the center rod, which is already plenty strong with the aforementioned settings.(If doing a helix with a very high number of links(like over 100) then you may want to have that center rod print solid)
No supports needed
Make sure you have good bed adhesion as this model has a lot of small parts that need to stick to the bed. Even if the first layer goes down fine, the most frequent point of failure is with the small hubs in between the links as they have a very small point of contact with the bed. For the first 2mm of height before they bridge together and connect, there's a solid chance the nozzle might knock a couple off. If this happens, don't worry. In my experience this doesn't ruin the print and if you let the print finish, it will still work fine. This just leaves a small visual imperfection where the hub should have been, and can(it doesn't always!) make the helix turn slightly worse, but it can still be smoothed out as detailed below.
Helixes where the ends of the links are rounded are much more prone to warping, so for the Rounded Rectangular, Rounded Jagged, and Full Circle helixes, you may want to turn down your build plate temperature if you are having issues with the ends of the links curling up. This can cause slight visual defects, make the ends of the links be stuck together (they can be broken apart after printing), and cause the nozzle to break a link off the build plate leading to a failed print in a worst case scenario.
If you print a helix and it is permanently fused, you can adjust your horizontal expansion(the name will differ slightly based on the slicer) to make the tolerances looser. This design uses a mix of 0.3 and 0.4mm tolerances that most printers can handle though.
After you've printed your helix, congratulations! you now have a shiny slab of plastic! Depending on your printer, all the links may spin great straight off the build plate, or they might be a bit stuck. The result depends fully on your printer! For a worst case scenario, here's your ultimate guide to freeing up a stuck helix! Step 1: We need to make sure the links aren't fused to adjacent links. Take one end of a link, starting at one of the ends of the helix, and bend it slightly away. Your goal is to make sure it's not stuck to the link next to it in any way. If it won't flex away, it might be stuck and you need to stick something between them(like a flathead screwdriver) to force them apart. Repeat this for every link, on both ends of the link. Step 2: We are now going to break the center of each link free, one by one. Again, start at one of the ends of the helix. Grab a single link, and twist it sideways slightly. Your goal is to break it free from the center hubs/rod it spins on. Remember it is connected to the adjacent links so if those links are still stuck it will only rotate SLIGHTLY before it is stopped. Your only goal is for it to be broken free from the central hubs/rod, so if it can turn slightly in each direction then it's free and you can move on to the next link. Freeing up the last link can be a lot harder as with all the other links freed up, there's no good place to grab it if you need a lot of force to free up the link. I really don't have a solution for this, just keep trying to twist that final link free if it's stuck! You will know the helix is free if you can turn the central rod by the hubs without any links turning with it. Remember that with a semi-decent printer, you don't need to do this and all links can be freed up easily with a slight twist.
Now, to break in your helix for the smoothest spins!
First off, if you want to get a good baseline idea of how well the helix turns overall, try turning the center hubs and feeling for any resistance/friction. You don't need to turn it by the ends, instead "roll" it with your fingers by the hubs that are in between the links. This also provides another way to fidget with your helix :) Now, to get your helix to the best it can be, your goal is to rub the rough 3d printed parts together to smooth them out. To do this, grab 10 to 15 links on one of the ends of the helix while holding the other end of the helix with your other hand, and then turn them while both pulling away AND bending them at a slight angle. If you can hear the plastic gripping and making a bit of a grating noise, then you know it's working. Keep rotating them back and forth until either you can't feel it rubbing on itself anymore or until the helix is as smooth spinning as you want it. Make sure to do this for both ends of the helix! In my experience trying to do this with the links in the middle doesn't really work much, and just breaking in the ends makes the whole helix spin MUCH better even without doing anything to the links in the middle.
Congratulations! You made a helix! if you enjoyed this model, I would appreciate reviews, makes, and feedback!
Using the Customizer
This section is on using the OpenSCAD customizer to make your own helix! You will need to have OpenSCAD for this. Note that it is a complex model and helixes with a higher number of links can take 20+ minutes to render. With that out of the way, here's all the variables you can adjust!
The $fn value adjusts the resolution of the cylinders of the model. I turn it to 100 for printing, but for testing out different helix variables in OpenSCAD it loads a LOT quicker if you turn it down to a lower value like 30.
The Helix Link Number adjusts how many links are in the helix. Each link is 3mm wide, so ten links is 30mm long and so on. For a complete 180 degree twist with the default rotation between links, it takes about 15 links for a full rotation of the links.
The Visual Link Rotation adjusts the visual rotation of the links, this is for visuals in OpenSCAD only and does not adjust the actual amount the links can rotate when printed. This is just to get an idea of what it will look like when twisted after printing. Set this value equal to the Rotation Between Links to get an idea of what it will look like. Set to zero before exporting and printing.
The Link Length Diameter affects how long the links on the helix are. This number is in mm and is the total length of each link. A longer link makes the helix's spiral look more "compressed" despite it not actually affecting how much the links can rotate. To get a better idea of what it looks like when rotated, use the "Visual Link Rotation". Note that this setting is not available for HalfCircle or FullCircle helixes.
The Angled Link Length changes the angles of the sides of the helix by making each link slightly longer than the previous link. The number is in mm and is how much longer lengthwise each link will be than the previous one, and is added onto the Link Length Diameter. For example, a value of 6 will give 45 degree angled sides. This is good for making tree shaped helixes! Note that this setting is not available for HalfCircle or FullCircle helixes.
The Extend End Hubs makes the hubs at the two ends of the helix longer, which can make it easier to hold and spin by the ends. Each number(example:1) adds 1mm of length to each end hub, making them protrude out that distance. The Spinning Stand also has a matching variable that has to be adjusted for this to still fit.
The Rotation Between Links affects how far each link can rotate before being stopped by the adjacent links. The number is in degrees, so at 12 each link can rotate +- 12 degrees in either direction. A higher value will lead to a tighter twist, and vice versa. The max value this should be put at is 12.5, there is not enough vertical room to put it higher than that unless the Linking Nub Thickness value is lowered. All Helixes I upload have this set to 12.
The Add Christmas Star setting adds a star on top of the helix, this type of helix cannot be used with the Spinning Stand. I also recommend setting the Angled Link Length to 2 when using this, so you then get a Christmas tree looking thing. I also like to set Extend End Hubs to 12 to give the tree a base. This setting is on/off only, and the star is not customizable. While active the Extended End Hub on the side with the star is disabled, so it will only come out of the side opposite it if that variable is set higher than 0.
The Linking Nub Thickness controls how thick the nubs in the links that carry over the rotation are. I HIGHLY ADVISE leaving this setting alone unless you know what you are doing and want to experiment. The number does not correspond to any particular unit of measurement, but a higher one will give thicker nubs and a smaller one will give thinner, and therefore weaker, nubs. A smaller value can allow the Rotation Between Links value to be increased slightly further.
The Spinning Stand also has its own customizer. You have to set the Helix Link Number and the Extended End Hubs value equal to the helix you want it to fit. Note that most helixes uploaded by me will have the Extended End Hubs at 0, unless otherwise stated in the file name.
Extra notes
This section is for any random extra bits of information that don't fit in elsewhere!
I don't really mention this anywhere else, but for the helixes with an Angled Link Length I set the Link Length to 22mm.
I would also like to mention that the 40 link HalfCircle helix in some of the photos is too big to fit on a standard 220 by 220 build plate, but the 256 by 256 build plate size most Bambu labs printers have can fit it.
Do you want to add some extra flair to your helix? try color changes! If you swap out the color halfway through, It can look even more impressive! But you don't have to stop there! With a AMS or other multicolor compatible printer, you can experiment with so much more!
I might make a second premium helix pack in the future with even more helixes, leave a comment if you would be interested in something like that!
Do you want to sell these helixes commercially? if so, assuming you have purchased this pack, go right ahead!
If you have any questions or need help with anything, ask in the comments!