Linked Helix Christmas Tree (Kinetic DNA Spiral Toy/Art Piece)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is a series of links that are interconnected to form a spiral when twisted. It prints in place and has a stand too.
- Ocena
- 0 / 5
- Polubienia
- 51
- Pobrania
- 195
- Wydruki
- 0
- Wyświetlenia
- 771
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Art & Designs
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Introducing the Linked Helix!
This design prints flat on the buildplate as a Print-in-Place design, but then with a twist elegantly spirals into a helix. It is made up of a series of links that all freely spin around an central axis, but the “twist” is that as each link turns, after it turns a certain amount, it turns the adjacent links along with it and so on in a cascading effect! This creates a elegant arch that can spin about freely and makes an impressive looking and fun fidget toy. It's also fairly durable! This particular helix is in the shape of a Christmas tree and is a free sample from my premium helix pack.

Do you like these helixes and want more? Check out my Premium helix pack at the link below with 1000s of fancier helix combinations!
https://www.printables.com/model/1512382-linked-helix-premium-pack-1-kinetic-dna-spiral-toy

More information on this Helix
This helix makes an excellent fidget toy that doubles as a stunning decoration both sitting on a shelf and in motion. There is also a stand to print to hold the Christmas tree vertically, which would be needed to display it, although it's of no benefit for fidgeting. As I mentioned earlier, this is a free sample from my premium helix pack, which is fully parametric and allows for thousands of different unique helixes to be easily generated in OpenSCAD. This helix is the perfect Christmas decoration to show off the capabilities of 3D printing, or just to impress people in general.
Print settings and post-processing
Material: I used PLA, although any similar material like PETG should work fine as well. This helix takes around 85 grams, and the stand takes 5-6 grams.
Size: This particular helix is quite large and will not fit on a mini sized printer, although you could generate a smaller one with the premium pack. It fits on a 220 x 220mm build plate like on an Ender 3, so most standard printers can print this.
0.4mm nozzle, 0% infill, and 2 wall lines-the weakest part of the helix is the center of the links which prints solid even with just two wall lines, so there is next to no advantage to adding infill or doing more than 2 wall lines. The only part that gains any real strength is the center rod, which is already reasonably strong with the aforementioned settings.
No supports needed
Make sure you have good bed adhesion as this model has a lot of small parts that need to stick to the bed. Even if the first layer goes down fine, the most frequent point of failure is with the small hubs in between the links as they have a very small point of contact with the bed. For the first 2mm of height before they bridge together and connect, there's a solid chance the nozzle might knock a couple off. If this happens, don't worry. In my experience this doesn't ruin the print and if you let the print finish, it will still work fine. This just leaves a small visual imperfection where the hub should have been, and can (it doesn't always!) make the helix turn slightly worse, but it can still be smoothed out as detailed below.
Helixes where the ends of the links are rounded like this one are much more prone to warping, so you may want to turn down your build plate temperature if you are having issues with the ends of the links curling up. This can cause slight visual defects, make the ends of the links be stuck together (they can be broken apart after printing), and cause the nozzle to break a link off the build plate leading to a failed print in a worst case scenario.
If you print a helix and it is permanently fused, you can adjust your horizontal expansion(the name will differ slightly based on the slicer) to make the tolerances looser. This design uses a mix of 0.3 and 0.4mm tolerances that most printers can handle though.
After you've printed your helix, congratulations! you now have a shiny slab of plastic! Depending on your printer, all the links may spin great straight off the build plate, or they might be a bit stuck. The result depends fully on your printer! For a worst case scenario, here's your ultimate guide to freeing up a stuck helix! Step 1: We need to make sure the links aren't fused to adjacent links. Take one end of a link, starting at the bottom of the tree, and bend it slightly away. Your goal is to make sure it's not stuck to the link next to it in any way. If it won't flex away, it might be stuck and you need to stick something between them(like a flathead screwdriver) to force them apart. Repeat this for every link, on both ends of the link. Step 2: We are now going to break the center of each link free, one by one. Again, start at the bottom of the helix. Grab a single link, and twist it sideways slightly. Your goal is to break it free from the center hubs/rod it spins on. Remember it is connected to the adjacent links so if those links are still stuck it will only rotate SLIGHTLY before it is stopped. Your only goal is for it to be broken free from the central hubs/rod, so if it can turn slightly in each direction then it's free and you can move on to the next link. You will know the helix is free if you can turn the star on top without any links turning with it. Remember that with a semi-decent printer, you don't need to do this and all links can be freed up easily with a slight twist.
Now, to break in your helix for the smoothest spins!
First off, if you want to get a good baseline idea of how well the helix turns overall, try turning the center hubs and feeling for any resistance/friction. You can turn it by the star or "roll" it with your fingers by the hubs that are in between the links. This also provides another way to fidget with your helix :) Now, to get your helix to the best it can be, your goal is to rub the rough 3d printed parts together to smooth them out. To do this, grab 10 to 15 links on the bottom of the helix while holding the other end of the helix with your other hand, and then turn them while both pulling away AND bending them at a slight angle. If you can hear the plastic gripping and making a bit of a grating noise, then you know it's working. Keep rotating them back and forth until either you can't feel it rubbing on itself anymore or until the helix is as smooth spinning as you want it. In my experience trying to do this with the shorter links doesn't work as well, and just breaking in the bottom makes the whole helix spin MUCH better even without doing anything to the links in the middle.
Congratulations! You made a tree helix! if you enjoyed this model, I would appreciate reviews, makes, and feedback!
Extra notes
This section is for any random extra bits of information that don't fit in elsewhere!
Want to know the settings used to generate this helix? The file name tells you just about all of the parameters used and if you want a guide on how to understand it, just look in the description of the premium helix pack mentioned above!
Do you want to add some extra flair to your helix? try color changes! If you swap out the color halfway through, like with the helix in the cover photo, It can look even more impressive, but you don't have to stop there! With a AMS or other multicolor compatible printer, you can experiment with it so much more!
Do you want to sell this helix commercially? if so, I grant you permission to do so ONLY IF you purchase the premium helix pack(available on the Printables Store at the link above). For just $8, you can have the commercial rights to sell these helixes!
If you have any questions or need help with anything, ask in the comments!