1 / 3
SV08 BTT Eddy Mount for LDO Jabberwocky — zdjęcie 1
1 / 3

SV08 BTT Eddy Mount for LDO Jabberwocky

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A mount to use BTT Eddy with LDO Jabberwocky Toolhead

Ocena
0 / 5
Polubienia
8
Pobrania
36
Wydruki
0
Wyświetlenia
417
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Wiring

  • You must create or obtain a compatible cable for the LDO Nitehawk 36 USB connector in order to connect the BTT Eddy probe.
    A standard cable is not included and must be sourced or made separately.

Mounting Hardware

  • Use M4 × 6 mm screws to level/adjust the mount.  This adjustment screw was added to compensate and ensure proper alignment.

  • Use M3 × 16 mm screws to secure the mount to the toolhead. Ensure the screw securing the toolhead is shorter to prevent interference with the Eddy mount during installation.

Initial Probe Positioning

  1. Manually lower the nozzle until it just touches the bed.

  2. Place the included 2 mm spacer/sheet between the BTT Eddy probe and the bed.

  3. While the spacer is in place, tighten the mounting screws to lock the probe height.

  4. Remove the spacer before homing or probing.


⚠ Disclaimer

This mount is provided as-is.
I am not responsible for any damage to your printer, toolhead, bed, or electronics resulting from installation, wiring, or calibration.
Proceed only if you understand the risks and are comfortable working on your printer.


Printer configs:

[stepper_x]
step_pin: PE2
dir_pin: !PE0
enable_pin: !PE3
rotation_distance: 39.80        
microsteps: 16           
full_steps_per_rotation:200   
endstop_pin: tmc2209_stepper_x: virtual_endstop              
position_min:-15           
position_endstop: 342       
position_max: 342           
homing_speed: 25              
homing_retract_dist: 0        
homing_positive_dir: True   

[stepper_y] step_pin: PB8 dir_pin: !PB6 enable_pin: !PB9 rotation_distance: 39.80
microsteps: 16
full_steps_per_rotation:200
endstop_pin: tmc2209_stepper_y: virtual_endstop
position_min: -5
position_endstop: 362 position_max: 362 homing_speed: 25
homing_retract_dist: 0
homing_positive_dir: true

[stepper_z] step_pin:PC0
dir_pin:PE5
enable_pin:!PC1
rotation_distance: 40 gear_ratio: 80:12
microsteps: 16
endstop_pin: probe:z_virtual_endstop position_max: 347
position_min: -0.5
homing_speed: 15.0 homing_retract_dist: 1.5 homing_retract_speed: 15.0 second_homing_speed: 10.0

[quad_gantry_level] gantry_corners: -60,-10 410,420 points: 40,5 # Point 1 40,285 # Point 2 335,285 # Point 3 335,5 # Point 4 speed: 500 horizontal_move_z: 2 retry_tolerance: 0.0085 retries: 10 max_adjust: 30

[mcu eddy]

FOR USB: replace this with your serial port ID

FOR CANBUS: replace this with your canbus UUID

serial: /dev/serial/by-id/usb-Klipper_rp2040_50445061305E751C-if00 # validate and set the correct serial Id restart_method: command

[probe_eddy_ng btt_eddy] sensor_type: btt_eddy i2c_mcu: eddy i2c_bus: i2c0f x_offset: -25.0 y_offset: 25.0

[temperature_sensor btt_eddy_mcu] sensor_type: temperature_mcu sensor_mcu: eddy min_temp: 10 max_temp: 105

[temperature_sensor btt_eddy] sensor_type: Generic 3950 sensor_pin: eddy:gpio26

Important Note

This mount is my own original design. The foundational toolhead measurements were referenced from “LDO Jabberwocky SV08 Mount (SV08, SV08 MAX, SV08 ZERO)” by Valerie Moore, and full credit is given to her for those measurements.

Here the model: 

Thanks and Happy Printing!!!!

Tagi