16-fach Zimtstern Ausstecher mit Eischnee-Schablone (Cinnamon star cookie cutter)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
16-fach Zimtstern Ausstecher mit Eischnee-Schablone. Damit kann man in 5 Minuten 32 nahezu perfekte Sterne ausstechen.
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 95
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Share Alike
English version below
Wir haben damit >300 Zimtsterne ausgestochen. Am Ende haben wir 5 Minuten für 32 fast perfekte Sterne benötigt.
Ich habe alles mit PLA+ gedruckt.
Die Abstandshalter ("Spacer") habe ich mit 0,25 mm Schichtdicke, 2 Perimeter und 70% Infill gedruckt.
Alle anderen Teile mit 0,2 mm Schichtdicke, 2 Perimeter, 15% Infill.
Ausstechen
Teig und Eischnee nach Rezept vorbereiten.
Teig mit Hilfe der Abstandshalter auf 7mm Dicke ausrollen (Abstandshalter sind 7x6mm).
Den Ausstecher ("Cutter") darauf legen und mit dem Nudelholz in den Teig drücken.
Den Ausstecher mit Hilfe des Gegenstückes ("Press") herausnehmen.
Die Eischnee-Schablone ("Stencil") auf die Sterne legen.
Den Eischnee mit einem Messer (o.ä.) darauf streichen und glatt abziehen.
Die Eischnee-Schablone vorsichtig senkrecht nach oben abnehmen.
Die Sterne mit einem Messer von der Arbeitsplatte lösen und auf ein Backblech legen.
Tipps
Der Teig sollte klebrig genug sein, damit er auf der Arbeitsplatte kleben bleibt.
Die Eischnee-Schablone nach jedem Einsatz mit warmen Wasser reinigen.
Den Ausstecher vor jedem Einsatz mit Puderzucker bestäuben.
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
We cut out >300 cinnamon stars. In the end, it took us 5 minutes to make 32 almost perfect stars.
I printed everything with PLA+.
I printed the spacers with a layer thickness of 0.25 mm, 2 perimeters, and 70% infill.
All other parts were printed with a layer thickness of 0.2 mm, 2 perimeters, and 15% infill.
Cutting
Prepare the dough and topping according to the recipe.
Roll out the dough to a thickness of 7 mm using the spacers (spacers are 7x6 mm).
Place the cutter on top and press it into the dough with a rolling pin.
Remove the cutter using the counterpart (“press”).
Place the topping stencil on the stars.
Spread the topping on top with a knife (or similar) and smooth it out.
Carefully remove the topping stencil vertically upwards.
Use a knife to loosen the stars from the work surface and place them on a baking sheet.
Tips
The dough should be sticky enough to stick to the work surface.
Clean the topping stencil with warm water after each use.
Dust the cookie cutter with powdered sugar before each use.