Ridgid Circular Saw R8656B Wall Mount/Holder
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Brackets/holder parts to mount your Ridgid Circular Saw (model # R8656B) on a wall.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 22
- Wydruki
- 0
- Wyświetlenia
- 140
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
I got a Ridgid Cordless Circular Saw (model # R8656B) and wanted to store it out of the way on the wall.
The model comprises two main parts, a top and bottom, which hold the saw to a board. You can then attach this board to wall in whichever way is appropriate to you. In my case, this is held on the wall using my French cleat system.
There is a third part, which helps with pulling back the circular saw blade guard when inserting the saw into the holder. Be forewarned though that, in order for this part to be effective when using a French cleat system, you need to also install something that prevents the backer board from moving upward. You can always just use two hands when inserting the saw, in which case, this part is not necessary.
Hardware needed:
Backer board: I used a piece of 5/16-in thick (actual) plywood but even something as thin as a 5mm underlayment board would work just as well. It needs be at least 6-in wide (15 cm) and 12 3/8-in (31.2 cm) tall.
7x M4 screws and nuts (6x if not using the blade guard catch): Flathead screws are recommended. This is so that the heads can be made flush with a countersink, thus preventing the screw heads from interfering with how you mount the board on the wall. The length of the screws will depend on the thickness of your backer board, and should be 6 mm longer than the thickness of the board. For example, for a 5/16-in (~8 mm) thick board, one should use 14 mm long screws.
Printing: No special settings or supports are needed when printing. If necessary rotate the top and bottom parts so that the face with openings for the hex nuts are down on the print bed. 3 perimeters are highly recommended since the print must be strong enough to prevent the hex nuts from spinning when tightening the screws.
Assembly:
It is much easier if you install the top part first. Trace a horizontal line so that the part stay level and the screw locations line up. Then set the top part next to but aside this line and mark where to drill. Drill and screw the top part.
Put the backer board down on a table. Grab the circular saw and pull the blade all the way up. The blade should be above the baseplate (even though the blade guard will still extend past it). Hold the blade guard back with one hand so that the baseplate can sit straight on the backer board (see attached photo on when the circular saw is on the wall mount), and insert the front on the top part, pushing forward all the way.
Set the bottom part on the backer board just bellow the back of the circular saw baseplate. This should be such that when one lifts the circular saw, as if hinging on the top/front part, the back of the baseplate clears the bottom part. Mark a line at the bottom of the part.
Mark the line for the bottom part screws 5/16-in (8 mm) above (i.e., toward the top part) the line from the previous step. Then, mark, drill and screw the part just as in step 1. Now, if you insert the circular saw in the top part, as in step 2, and then pull back/let it slide down onto the bottom part, it should still be held at the front, thus holding the circular saw. To take the circular saw out, simply reverse the order of the instructions in the previous sentence.
Lastly, to install the blade guard catch, first insert the circular saw onto the holder with the back all the way against the bottom part. The blade guard catch should be placed vertically so that it barely holds the blade guard in this position and centered with the inner part of the blade guard (i.e., the "lip" that pushes back the blade guard when cutting).
This was designed to fit a 6.5-in Ridgid Cordless Circular Saw (model # R8656B). This may fit other models also... If you retrace the front and back of your circular saw baseplate, you can compare to the dimensions in the attached FreeCAD or STEP model files.