N-Works Heat Insert Press
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A heat press using the PLS 48 C1 Soldering Iron from Parkside.
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 184
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Ideas
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A heat press using the PLS48C1 Soldering Iron from Parkside.
!Important!
When pushing down, grab the whole sled! Grabbing only the soldering iron can make the press tip over.
Soldering Iron info:
The PLS48C1 is discontinued by Parkside and I can't check if the PLS48D2(current version) fits. The Felicidade Soldering Iron fits as well. To install the Felicidade replacement push it in before sliding the sled on the rods. Fixate it with 3 M5X5mm flat-tip set screws through the already existing holes in the sled. When choosing the Felicidade option you won't need the following parts: Housing; Cable Plate; Lid. Since these are used to hold the Parkside electronics
Sourcing guide: OneDrive sheet
Assembly guide: Youtube
Parts needed:
Soldering Iron:
Part | Quantity | Comment | Sourcing Tip | Price | Source |
|---|---|---|---|---|---|
Parkside PLS48C1 | 1 | Discontinued but still can be found used | ???€ | ||
or | |||||
Felicidade | 1 | Fits as well. Check description for install instructions. | 18,99€ |
Hardware:
Part | Quantity | Comment | Sourcing Tip | Price | Source |
|---|---|---|---|---|---|
Alu Extrusion 160mm | 1 | Can be wider. Printed parts need at least 160mm to grip completely. | 2,95€ | ||
Alu Extrusion 300mm | 1 | Can be changed alongside the rods. Limits the up/down travel. | 4,33€ | ||
Rods 8X320mm | 2 | Can be changed alongside Alu Extrusion 300mm. Limits the up/down travel. | 9,59€ | ||
Bearings LM8LUU 5X15X45mm | 2 | Remember to lubricate them to reduce wear. | 2,89€ | ||
Screws M6X12mm | 34 | Better Source from local Hardware store. MC Master-Carr link contains pack of 100Pcs. | 9,29€ | ||
Nuts M6 | 30 | 28Pcs work as well since 2 Nuts in the housing ankers aren't used. | Better Source from local Hardware store. MC Master-Carr link contains pack of 100Pcs. | 2,67€ | |
Flat-Tip Set Screw M5X5mm | 3 | You only need these when choosing the Felicidade Soldering Iron. | Better Source from local Hardware store. MC Master-Carr link contains pack of 100Pcs. | 9,50€ | |
Spring | 1 | I used an old Bowden Extruder spring. | Length: 20mm Wire diameter: 1,2mm Outer diameter: 9mm | 1,55€ |
Printed Part:
Part | Quantity | Comment | Sourcing Tip |
|---|---|---|---|
Anker X1 | 2 | Print with support. | Print yourself or order from N-Works |
Anker X3 | 10 | Print with support. | Print yourself or order from N-Works |
Bottom | 1 | Print with support. | Print yourself or order from N-Works |
Cable Clip | 1 | Can be split to fit smaller printers with no worrys. | Print yourself or order from N-Works |
Cable Plate | 1 | Print as is. | Print yourself or order from N-Works |
Chain Base | 1 | Print with support. | Print yourself or order from N-Works |
Chain Clip | 13 | Print as is. | Print yourself or order from N-Works |
Chain End | 1 | Print as is. | Print yourself or order from N-Works |
Chain Link | 12 | Print as is. | Print yourself or order from N-Works |
Corner | 2 | Print as is. | Print yourself or order from N-Works |
Housing | 1 | Print with support. | Print yourself or order from N-Works |
Lid | 1 | Print with support. | Print yourself or order from N-Works |
Sled | 1 | Print with support. | Print yourself or order from N-Works |
Stopper | 1 | Print with support. | Print yourself or order from N-Works |
Top | 1 | Print with support. | Print yourself or order from N-Works |
Tips:
Put the Bearings in the freezer a good time before assembly to make it easier.