1 / 7
Bestway Shade Pool 2.4m 561GA(~) T Connector (120) and Foot — zdjęcie 1
1 / 7

Bestway Shade Pool 2.4m 561GA(~) T Connector (120) and Foot

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A chonky replacement T connector for a Bestway Shade Pool (2.4m) and a foot

Ocena
0 / 5
Polubienia
1
Pobrania
24
Wydruki
0
Wyświetlenia
121
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

This is a chunky version of a T connector for a Bestway Shade Pool and earlier versions, the kind you can purchase from Kmart (Australia) etc. there is also a model for a foot replacement but I'm mostly focused on the T connector in my rants below as it was a PITA.

I previously used the model here (thanks @marcel293) but constantly broke the thing and got sick of wasting filament printing it so instead I decided to waste my brain trying to reproduce and then chunking it up to make it more printable, then wasted filament anyway by getting the diameter maths slightly wrong the first time.

I think my issue with the previously used model was that it didn't have stop points at the same point as the original, so you could easily put the pole in too deep which then increased the strain, alternatively my wife is a wave woman and just absolutely abused the thing (to be fair she did break the original part this was replacing).

I created this using Onshape. The document is here. Feel free to modify/do whatever with it. There are a few part studios there, the original T mostly 1:1 (think I closed the central point that's about it), this modified more printable version and a replacement foot. Please cover your eyes with the "make it more printable" folder, basically headbutt the various fillet/chamfer/what not tools until my slicer looked relatively happy. Note: I learnt CAD by headbutting the keyboard because I bought a 3D printer, I'd imagine none of it is "optimal", hell I probably learnt things and did it better as I went further into this model (worked out how to use mirroring/patterns later).

This is basically the original part with some mods:

  1. Thicker pole holes

  2. Tried to make as much of the stuff that the slicer was going to waste filament on supports as just a solid piece - this means the whole top half is more of a table than a pipe. The only place that I end up with supports is the pole hole internals, which sucks but so do I so I can't complain.

  3. No void between pole stop points - hard stop so you can't over insert the poles, I think this was a big reason the previous model failed me but figured if I'm wasting filament may as well make sure it won't break / was easier to print, hence going nuts elsewhere

  4. Thicker bracing

The foot model is similar:

  1. Thicker pole holes

  2. Modified so no supports required (base wasn't flush, made flush but added some "grip" that's printable)

  3. Thicker bracing

  4. Kept random holes, I guess for water removal? Who knows maybe just some moulding thing, enjoy holes

  5. Printed same as T connector, although I dropped the walls to 6 from 8 to avoid print head movements - originally had the base grip all fancy and my printer hated me (and the print failed)

Print settings:

  • Depends how nuts you want to go, but I went a little nuts because I was sick of reprinting the previous model

  • Walls/Top/Bottom: 8

  • Infill: 44% - Gyroid

  • Filament: PETG - I was previously using ASA, so this potentially helps as well as it should be more flexible.

  • Supports: Yes - unless you're feeling lucky. The diameter of the pipes forces your hand there.

  • Brim: Yes - because my slicer on Auto brim decided to use one, but honestly I doubt it matters

  • Filament: 200g as per Orca Slicer - which is a bit ridiculous and I'm probably better off not doing the maths price wise. Again feel free to lower the above settings significantly I was just sick of the disappointed look from my wife when the connector breaks again and one 200g part is cheaper than 3 100g parts.

  • Time in my case (Creality K1): 6 hoursish. I think infill in particular was overboard, could probably drop significantly.

In my case with Voxelab PETG Pro on a Creality K1 it was cranked (260 hotend, 85 plate, lid off, no fans) because I wanted it to be a molten pile of plastic, YMMV. Considered leaving the lid on and putting it in a sauna but the internet scared me talking about things like "heat creep" and "clogged nozzles" and I'm too lazy for that kind of noise.

Photos show the end result for both models, the very old box and the listing on the Bestway website that seems to match this product (although it's a "newer" version, mine is fairly old, looks exactly the same though).

Other files contains gcode I used for a Creality K1 with Voxelab PETG Pro using "very strong use a lot of filament" settings. I'd probably slice yourself but these worked for me if you have a similar setup, could not upload to gcode section as some directives didn't parse.

Tagi