1 / 2
Halter Schwanenhals-LED für / clamp for goose neck LED lamp for TOMLOV /ELIKLIV Flex microscope — zdjęcie 1
1 / 2

Halter Schwanenhals-LED für / clamp for goose neck LED lamp for TOMLOV /ELIKLIV Flex microscope

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

clamp to attach a gooseneck LED lamp to the TOMLOV/ELIKLIV microscope arm

Ocena
0 / 5
Polubienia
0
Pobrania
6
Wydruki
1
Wyświetlenia
85
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

----for english, please scroll down----

Eine einfache Klemme zur Befestigung der abgebildeten Schwanenhalslampe (Link zu Aliexpress: https://www.aliexpress.com/item/1005006422623462.html "clamp type"-Variante - aber besser selber suchen, die Preise für das Teil schwanken je nach Anbieter ganz erheblich!) am Arm eines TOMLOV/ELIKLIV Flex-Mikroskops.

Benötigt wird die Klemme, zwei M3-Schrauben mit einer Länge von mindestens 12 mm, zwei M3-Sechskantmuttern, eine M4-Sechskantmutter und eine M4-Schraube mit einer Länge von 20 mm (25mm sollte auch okay sein).

Montage:

  • Muttern einpressen - die M3-Muttern außen, die M4-Mutter in der Mitte.

  • Die M4-Schraube wird in die Unterseite der Klemme eingesetzt und stützt die Klemme gegen das Metallteil des Mikroskoparms ab (siehe Bild bei "Make"), da ich der Plastik-Kabelführung des Arms das nicht zutraue. Die Schraube so eindrehen, daß sie 12mm in den Schlitz ragt (Bild 2). Bei einer Schraube mit 20mm Länge ist das der Fall, wenn die Schraube einfach auf Anschlag eingeschaubt wird.

  • Um Scheuern der Kabel zu vermeiden, ein 12mm langes Stück Schrumpfschlauch auf die Schraube stecken.

  • Dann die Kabel des Mikroskops in the Kabelführung einlegen, die Kabelführung auf den Arm des Mikroskopständers  aufclipsen (Ausrichtung wie im Bild) und danach den Halter über die Kabelführung stecken. Dabei darauf achten, daß die Kabel links und rechts an der M4-Schraube vorbeilaufen.

  • Nun die Lampe mit den beiden M3-Schrauben am Halter befestigen.

Gedruckt aus PLA, Supports habe ich keine benötigt.


A simple clamp to attach the shown goose neck lamp (link to Aliexpress: https://www.aliexpress.com/item/1005006422623462.html "clamp type" variant - but better search for yourself, the prices for that thing vary significantly!) to the arm of a TOMLOV / ELIKLIV Flex microscope arm.

You need this part, two M3 screws of at least 12mm length, two M3 hex nuts, one M4 hex nut and an M4 screw of 20mm length (25mm should be okay as well).

Assembly:

  • Insert the nuts into their places - the M3 nuts on the outsides, the M4 nut into the centre.

  • The M4 screw is inserted into the bottom of the part and rests against the metal part of the microscope arm since I do not trust the plastic cable guide of the arm to support the clamp. Screw it in until it protrudes 12mm into the slot (2nd picture). If the screw has  a thread length of 20mm, simply screw it in until the head hits the printed part to achieve this.

  • Preferably, add a 12mm piece of shrink tube to prevent the screw rubbing against the cables when the microscope arm is moved.

  • Then insert the microscope cables into the cable guide, clip the cable guide onto the arm of the microscope stand (alignment as shown in the picture) and then place the holder over the cable guide. Make sure that the cables run past the M4 screw on the left and right.

  • Now attach the lamp to the holder with the two M3 screws.

Printed from PLA, I did not require any supports.

Tagi