1 / 1
10MHz (30m band) Coil for Gabil 50" Whip — zdjęcie 1

10MHz (30m band) Coil for Gabil 50" Whip

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is an improved design from my original 10MHz coil for Gabil 50" Whip.

Ocena
0 / 5
Polubienia
5
Pobrania
18
Wydruki
0
Wyświetlenia
113
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution

This is an improved version of my 30m loading coil for Gabil 50" whip. It should be MUCH easier to actually make. This print should work on most printers without needing support material (all overhangs kept to 45 degrees). PETG recommended. Another filament may work, but I have not tested. 

Bill of Materials

You should need the following parts to complete the build. Links provided for reference. 

1x 50" Whip Antenna - Amazon.com: Telescopic Whip for GRA-HF750T | Stainless Steel Replacement Antenna Element | 7–50MHz Adjustable Multi-Band for Ham Radio HF Antenna : Electronics

1x Flange Mount Male BNC with 1/2" (12.7mm) screw pattern - 112653 Amphenol RF | Connectors, Interconnects | DigiKey

1x M8-1.0 x 40mm Long Fine Set Screw - https://belmetric.com/m8x1-0-stainless-allen-set-screw-fine-thread-stud-din-913-flat-point

1x M8-1.0 Flange Nut - QXSKSLH 25 Pieces M8 Flange Nuts, M8-1.25mm Serrated Hex Flange Lock Nuts, 304 Stainless Steel,Plain Finish: Amazon.com: Industrial & Scientific

4x M3 Heat Set Inserts, up to 5mm long - https://www.amazon.com/HANGLIFE-Heat-Set-Threaded-Printing-Components/dp/B0CS6VZYL8/ref=sr_1_1_sspa

4x M3 Screws - https://www.amazon.com/VGBUY-600pcs-Assortment-Printer-Stainless/dp/B0D1XJ766V/ref=sr_1_5

Magnet Wire 1mm - https://www.amazon.com/MECCANIXITY-Enameled-Winding-Transformers-Inductors/dp/B0CYP7D6B8/ref=sr_1_3

M3 Ring Terminals - https://www.amazon.com/Copper-Terminals-Connectors-Barrel-Electrical/dp/B0BN6335H7/ref=sr_1_9

Wire for Counterpoise - I used 18g BNTECHGO Silicone Wire - I found 188 inches to be the right length for 10MHz. If you use a different wire, your length may be different.  https://www.amazon.com/BNTECHGO-Silicone-Flexible-Stranded-Impedance/dp/B01MPZJOYN/ref=sr_1_1

Tools

Soldering Iron (for soldering and heat-set inserts)

Solder

Flux

Wire cutters

Knife or Sandpaper (to strip enamel) 

Screwdriver

Pliers (optional)

Directions:

Print chosen file (PETG recommended) - Should not need support material

If using the model with heat-set inserts, insert M3 heat-set inserts into 4 bottom holes

Thread wire through bottom hole from outside into center BNC cavity

Strip and solder wire to center pin of BNC

Screw BNC into heat-set inserts or holes in the bottom (if using the "No Inserts" file, leave one screw out for now. You don't want to strip the plastic threads by putting the screw in and out a bunch).

Wind magnet wire TIGHTLY around coil and insert through top hole, leaving about 1.25 inches of wire sticking out of the top. Count the number of turns to make sure you didn't miss one. 

Strip the wire sticking out of the top. Wrap it clockwise around the big hole at the top, so it forms a circle the same size as the ridge around the hole. Wrapping clockwise helps it pull tight when you put the nut on later. Optional: Solder the circle you just made, so it holds together a little better. 

Insert the 8mm set screw backward into whip antenna. Thread on the flange nut. Mark the depth on the set screw with a Sharpie marker.

Thread set-screw into top of print. Make sure you do not thread in past the Sharpie mark you made. The threads should self-tap, but go slow. DO NOT OVERTIGHTEN, you can easily strip the plastic threads you just formed by overtightening. If you are worried the set screw might back out (none of mine have), you can throw in a drop of superglue, but make sure it the threads are clean where the flange nut goes and where the whip antenna attaches. 

Use the flange nut to pinch the loop of stripped wire to ridge on top of print.

Attach counterpoise to M3 ring terminal however you want. I recommend soldering a 2mm female mini banana connector to the ring terminal and a 2mm male mini banana connector to the wire, so you can plug and unplug the counterpoise. Alternately, check if your mini banana connector happens to fit nicely in the wire-side of the ring terminal. Mine did.

Remove one of the BNC screws, and use it to secure the M3 ring terminal to the flange of the BNC connector. If using the "M3 Inserts" file, you may want to add a drop of LocTite to stop it backing out. If using the "No Inserts" file, you may want to add a drop of superglue in the hole before inserting screw.

I included 2 versions of this model. One uses M3 heat-set inserts in the bottom to attach the BNC connector. The other is designed to screw M3 screws directly into the plastic. 

Coil Specifications:

19.5 microhenries

42mm length

32mm diameter

33 turns

Improvements in this version:

-Prints in one piece

-No supports needed to print

-Uses commercially available BNC connector without the need to modify

-Uses commercially available M8-1.0 bolt without the need to make your own bolt

-Added 10MHz text to the top of coil for easy ID

Tagi