Voron Trident Z-Endstop With Nozzle Wisher
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Replace the Z-Endstop of Voron Trident design by an improved version, featuring a silicone nozzle wisher.
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 49
- Wydruki
- 0
- Wyświetlenia
- 367
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- BSD License
Voron Trident Z-Endstop With Nozzle Wisher
This design was developed to replace the Z-Endstop of the Voron Trident design by an improved version, that also features a support for a silicone nozzle wisher.
I chose the Nozzle Silicone Brush for the Creality K1, K1C, since it is easily available. In my case bought it here: AliExpress FYSETC Official Store - https://de.aliexpress.com/item/1005008164354026.html.
Features
Compatible with easy to find self adhesive K1 silicone replacements
Compact, because it reuses the existing endstop space
Incorporates a dirt blocker, to avoid interference with the mechanical endstop
Uses the back location, where the printer still has space
Print Procedure
Use usual Voron profile to print the part. The part was designed to be printed without the need of supports. You have to orient it correctly, keeping the flat side facing down at your print bed.
Install Procedure
Assembly of the Part
These are the steps:
Remove the old Z-Endstop, disconnecting cables and removing screws
Move the pole system from the old to this part. It is recommend to use some soft glue to ensure stability.
Move the PCB to the new body
Reuse the PCB cover, since it is compatible
Release the screws of your print bed and force it to the front as much as possible, then re-tight the screws at that position.
Usable space is very constrained on the Voron Trident, forcing you to use the extremes of your Y axis.Attach a silicone wisher on the pocket
Installing on the Printer
Now place the body, reusing the T-Nuts of the old part. Don't tighten it completely. The required screws are now longer: M3x20mm.
Before tightening the new body, use a putty knife between the print bed and the part, to make sure it does not contact it directly. then tighten the screws.
A thin air gap helps thermal isolation.Reconnect the endstop cable.
Calibration Tips
Y-Axis
After this you have to recalibrate your Y axis, according to the Voron setup guides.
[stepper_y]
...
position_min = -1
position_endstop = 258
position_max = 258
...Please test your setup with care. When moving to the extreme, you should not hear the sound of your print head hitting the limit.
Z-Axis
Please test your Z-endstop for functionality before homing your printer. You have to follow Voron guides on how to fine tune the Z-endstop and finally recalibrate your Z-offset.
I have a Voron Trident 250 and my endstop configuration is this:
[safe_z_home]
home_xy_position = 147,257
speed = 100
z_hop = 10Or for sensorless homing:
[homing_override]
...
G1 X147 Y257 F15000
...Nozzle Wipe Macro
[gcode_macro NOZZLE_WIPE]
description: Cleans the nozzle on the rear silicone wiper pad.
gcode:
# --- Check for homing and ensure safe Z height ---
{% if not 'z' in printer.toolhead.homed_axes %}
G28 Z ; Ensure Z is homed if not already done
{% endif %}{% set SAFE_Z_HEIGHT = 20.0 %}
{% set current_z = printer.toolhead.position.z %}
Ensure Z is at least at SAFE_Z_HEIGHT (5mm).
{% if current_z < SAFE_Z_HEIGHT %}
G0 Z{SAFE_Z_HEIGHT} F600 ; Move Z up to 5mm
{% endif %}
--- Setup and Initial Move ---
G90 ; Use Absolute Positioning
M400 ; Wait for current moves to finish
{% set X0 = 215 %}
{% set X1 = 170 %}
{% set Y0 = 258 %}
{% set Y1 = 257.2 %}
{% set Y2 = 256.6 %}
{% set Z0 = -1.5 %}
{% set Z1 = -1.2 %}
{% set Z2 = -0.9 %}
{% set Z_END = 10 %}
First we travel to a edge, because a long filament tail forms after long pause in a hot state.
This makes sure that this tail is behing the nozzle on an area where no build plate can sustain
this excess. (X250, Y257)
The next move ensures this...
G0 X250 Y257 F6000
G0 Z{SAFE_Z_HEIGHT} F600
Fast travel to the start position (X165, Y257)
G1 X{X0} Y{Y0} Z0.5 F4800
--- WIPE PASS 1 (Z=0.3mm) ---
G0 Z{Z0} F600; Move Z down to 1.2mm
{% set WIPE_SPEED = 7200 %} ; 120 mm/s = 7200 mm/min
Sequence 1: 165,256 -> 215,255 (50mm X wipe)
G1 X{X1} Y{Y1} F{WIPE_SPEED}
Sequence 2: 215,255 -> 165,254 (50mm X wipe back)
G1 X{X0} Y{Y2} Z{Z1} F{WIPE_SPEED}
--- WIPE PASS 2 (Z=0.1mm) ---
M400; Wait for Z move
Repeat the same sequence for the second pass
Sequence 1: 165,254 -> 215,255
G1 X{X1} Y{Y1} F{WIPE_SPEED}
Sequence 2: 215,255 -> 165,256
G1 X{X0} Y{Y0} Z{Z2} F{WIPE_SPEED}
--- WIPE PASS 3 (Z=-0.2mm) ---
M400; Wait for Z move
Sequence 1: 165,256 -> 215,256 (50mm X wipe)
G1 X{X1} F{WIPE_SPEED}
Sequence 2: 215,256 -> 215,254 (3mm Y move)
G1 Y{Y2} F{WIPE_SPEED}
Sequence 3: 215,254 -> 165,254 (50mm X wipe back)
G1 X{X0} F{WIPE_SPEED}
--- Final Retraction ---
G0 Z{Z_END} F600; Move Z up to 10mm
M400; Wait for final Z move