Voron V0 Dragon / Rapid / Yavoth Burner - ZeroClick probe mount with brace
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Standalone ZeroClick probe mount option for the Dragon Burner, Rapid Burner, Yavoth, etc.
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 23
- Wydruki
- 0
- Wyświetlenia
- 320
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- GNU General Public License v3.0
This uses the M3 screw holes on the rear of the toolhead to mount a ZeroClick probe.
For use with Voron V0 style toolheads where these M3 mount points are typically unused. Also substitutes the "Brace_Straight.stl" or "Brace_Loop.stl" parts.
Adds 7mm to the rear of the toolhead.
BOM:
2x 6mm x 3mm Magnets
2x M3x5x4 Heat Set Inserts (Voron Spec)
2x M3 x 8mm BHCS or SHCS
2x 22-28 AWG Signal wire from magnet to toolhead (Length ~20cm each) (See ZeroClick install instructions)
There are options with the probe mount integrated. I chose to leave it standalone like zruncho3d suggests:
https://github.com/zruncho3d/ZeroClick/tree/main?tab=readme-ov-file#should-toolheads-build-this-in
Want to use an alternate mount for your toolhead? See my other model:
Update 2026.02.19 I have created a V2. This has changed the probe mount to a rectangular block, much easier to press in the magnets evenly and uniformly. Includes pathway to route cables out of the way from your vice and (optional) small zip tie mount.
For Klipper, I recommend using the Klicky macros.
For someone looking for a lightweight solution, below is what I compiled. The G0 commands will need adjusted for your printer.
[gcode_macro _PROBE_VARS]
variable_probe_angle: 44
variable_probe_dock_angle: 134
gcode:[gcode_macro _ATTACH_PROBE]
variable_f: 5000
gcode:
SAVE_GCODE_STATE NAME=attach_probe_state
SET_SERVO SERVO=zeroclick_servo ANGLE={printer["gcode_macro _PROBE_VARS"].probe_angle}
G90
G0 X50 F{f}
G0 Y103 F{f}
G0 X20 F{f}
G0 X50 F{f}
SET_SERVO SERVO=zeroclick_servo ANGLE={printer["gcode_macro _PROBE_VARS"].probe_dock_angle}
RESTORE_GCODE_STATE NAME=attach_probe_state
[gcode_macro _DETACH_PROBE]
variable_f: 5000
gcode:
SAVE_GCODE_STATE NAME=detach_probe_state
SET_SERVO SERVO=zeroclick_servo ANGLE={printer["gcode_macro _PROBE_VARS"].probe_angle}
G90
G0 X50 F{f}
G0 Y103 F{f}
G0 X20 F{f}
G0 Y50 F{f}
SET_SERVO SERVO=zeroclick_servo ANGLE={printer["gcode_macro _PROBE_VARS"].probe_dock_angle}
RESTORE_GCODE_STATE NAME=detach_probe_state
[gcode_macro BED_MESH_CALIBRATE]
rename_existing: _BED_MESH_CALIBRATE
gcode:
_ATTACH_PROBE
_BED_MESH_CALIBRATE {rawparams}
_DETACH_PROBE
[gcode_macro Z_TILT_ADJUST]
rename_existing: _Z_TILT_ADJUST
gcode:
_ATTACH_PROBE
_Z_TILT_ADJUST {rawparams}
_DETACH_PROBE
[gcode_macro PROBE_CALIBRATE]
rename_existing: _PROBE_CALIBRATE
gcode:
{% if not 'xyz' in printer.toolhead.homed_axes %}
{ action_raise_error("Must Home X, Y and Z Axis First!") }
{% endif %}
G90
_ATTACH_PROBE
G0 X85 Y40 F5000
_PROBE_CALIBRATE {rawparams}
M118 remove manually the probe and continue calibration