1 / 3
MMU3 Collet Holder R4 Mod.by Nigeke — zdjęcie 1
1 / 3

MMU3 Collet Holder R4 Mod.by Nigeke

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

MMU3 Collet Holder to Connect PTFE tubing and be FLEXIBEL

Ocena
5 / 5
Polubienia
5
Pobrania
18
Wydruki
1
Wyświetlenia
127
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

MMU3 Collet Holder R4 Mod.by Nigeke

When building the MMU3, I experienced some problems with regards to the PRUSA Collet Holder R4:

  1. All the PTFE tubes are absolutely fixed

  2. I can’t easily connect or reconnect another PTFE tube to change filament quickly and easily

  3. That all these PTFE tubes are absolutely fixed makes it impossible (or incredibly hard) to move the MK4S as from buffer to roll holders the PTFE-spaghetti tubing is fixed absolute to everything (Sometimes I do need to clean and move the 3D Printer and its components)

  4. The PRUSA solution is not flexible (and that’s the actual problem!)

Now one could easy criticize PRUSA on the original PRUSA Collet Holder R4 and the PRUSA provided collets, However: What PRUSA provides is actually very good quality and these collets might look poor but if you will try disconnecting a PTFE tube from these collets you will be convinced of the never lacking PRUSA quality! It’s just that it is not flexible enough for me. At first, I just tried to screw the PC4-M6 PTFE Hose Connectors in the original PRUSA Collet Holder R4 however that doesn’t work as the space reserved for the PRUSA provided collets will leave a little void on which filament will get stuck! And that’s why I needed to create this MOD.

Creating this MOD was not as straight forward as I expected as the filament path through the part is actually curved, the mounting holes are on a very particular angle and depth and avoid creating any catches where the filament gets stuck. So, I had to make it from scratch: measuring, adjusting, verifying, print prototype, testing, improving and repeat that till you get an acceptable result. If you are going to use it, I hope this works for you too.

To PRUSA: yes, you may use this MOD for the MMU3 in future on the condition you will use PRUSAMENT for it and definitely no bambu!

What you need:

  1. The Printed Part

  2. 5 pc. PC4-M6 PTFE Hose Connector (Collet)

  3. 5 pc. PTFE-tubing; Length exactly 20 mm, Outer diameter 4 mm; Inner diameter 2.5 mm (Make sure that Inner diameter is correct, see Notes below)

  4. M6(sp1) Bolt

  5. 5 mm flexible tube-brush

  6. PTFE-tube cutter (super sharp)

How to:

  1. Print the part, for this I recommend PRUSAMENT PETG, use: 0.1 Layer thickness, 2 mm shell thickness and 25% grid fill

  2. Cut 5 pc. PTFE-tubing at exactly 20 mm length (this needs to be accurate); check the tubes don’t use if damaged, bend, shreds (else make new piece)

  3. Use M6 Bolt to clean the 5 printed thread holes with moderate force and keep it straight (Please see notes below)

  4. Push the PTFE 20 mm tubes in the Printed Part from the side of the M6 threaded hole up to where the PTFE-tube is flush with the M6 hole

  5. Push the PTFE-tube in by screwing in the PC4-M6 PTFE Hose Connector (Collet); use moderate force and keep it straight

  6. Clean the hole with the flexible brush

  7. I recommend you also clean the holes on the MMU3 unit before fitting the MMU3 Collet Holder R4 Mod.by Nigeke and check for/remove any debris in the idler

  8. Now fit the Collet Holder R4 Mod.by Nigeke as per original PRUSA assembly guide; ensure that you can see the new PTFE-tubes as describe in the original PRUSA assembly guide. (If not the PTFE tubes where not the correct length, take it apart and do it again, this need to be perfect!)

  9. Now connect your PTFE tubing from buffer (or whatever setup you have) to the PC4-M6 PTFE Hose Connectors (Collets) on your new MMU3 Collet Holder R4 Mod.by Nigeke

  10. Now your flexible! As PRUSA said: HAPPY PRINTING!

Notes:

  1. Only .stl provided, no bgcode/gcode files: Use PRUSA slicer to make your own (they are printer/material dependent anyway)

  2. Use the best PETG you can get (PRUSAMENT is best choice here)

  3. Don't use a M6 thread cutter on the Printed Part to clean the thread, I use that often but on this Printed Part there is not enough depth, and you end up shredding the material adding to possible risk of debris in the MMU3. The bolt method works better, if needed you can also warm-up the bolt.

  4. Make sure to use correct PTFE tubing: Outer diameter 4 mm Inner diameter 2.5 mm. Lot of sold tubing with the said inner diameter is NOT that, check it when you receive it if anything below 2.3 mm send it back, as you got old standard dumped on you. A smaller Inner Diameter can cause difficulties with leading the filament through and that is incredibly annoying! 

As PRUSA said: HAPPY PRINTING!

Nigeke

Tagi