Adaptation of the AD5X spool holder for the Neptune 4 Plus (Адаптация катушкодержателя AD5X для Neptune 4 Plus)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Adaptation of the AD5X spool holder for the Neptune 4 Plus (Адаптация катушкодержателя AD5X для Neptune 4 Plus)
- Ocena
- 0 / 5
- Polubienia
- 18
- Pobrania
- 78
- Wydruki
- 0
- Wyświetlenia
- 625
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
Держатели катушки AD5X безынерционны и кроме того способны доматывать филамент обратно, если он случайно вытянулся, что позволяет избегать запутывания. Поэтому сразу же возникла идея приспособить их для Neptune 4 Plus, так как он частенько от такого страдает =) В итоге получилась вот такая простенькая штучка.
Печатается так, как показано на фото, а под резьбу я включал обычную поддержку (не древовидную).
Резьба, конечно, не получается идеальной, но:
1) Учитывая что шаг резьбы 1,5 мм, а допуски достаточно велики, адаптер вполне приемлемо вкручивается (с трудом только первый раз) и не болтается
2) При таком положении печати вся нагрузка на резьбе идёт поперёк слоёв, а значит шанс отрыв минимален
Кроме step-файла я размещаю и файл FreeCAD, если кому-то захочется поэкспериментировать. "Неровные" размеры модели в файле FreeCAD, это следствие подгонки допусков, вы вольны изменять как вам заблагорассудится. И прошу прощения за возможные огрехи, я не являюсь опытным пользователем FreeCAD xD
Режимы печати выбирайте какие вам удобней или привычней, я полагаю особой роли это не играет. Но для более аккуратной резьбы возможно будет полезным печатать от 0,2 и меньше. Кол-во периметров подгоните так, чтобы обеспечить толщину стенки 0.8-1 мм, а заполнение я ставил 25% тип "Крест"
AI translate
The AD5X spool holders are inertia‑free, and moreover, they can rewind the filament back if it accidentally gets pulled out — which helps avoid tangling. So I immediately got the idea to adapt them for the Neptune 4 Plus, since this printer often suffers from such issues =)
In the end, I came up with this rather simple little thing.
Printing instructions
Print it as shown in the photo. For the thread, I used standard (non‑tree) supports. The thread isn’t perfect, of course, but:
Given that the thread pitch is 1,5 mm and the tolerances are quite loose, the adapter screws in acceptably (it’s a bit tight the first time, but then it’s fine) and doesn’t wobble.
With this print orientation, the load on the thread runs across the layers, which means the risk of breakage is minimal.
Along with the STEP file, I’m also sharing the FreeCAD file for anyone who’d like to experiment. The “irregular” dimensions in the FreeCAD file are a result of fine‑tuning the tolerances — feel free to adjust them as you see fit.
Apologies for any imperfections — I’m not an experienced FreeCAD user xD
Print settings
You can use whatever print settings you’re comfortable with; I don’t think it makes a big difference. However, for a neater thread, it might help to use a layer height of 0,2 mm or less.
Adjust the number of perimeters to achieve a wall thickness of 0,8–1 mm.
I used 25% infill with the “Cross” pattern.