LayersFactory
Zgłoś model
1 / 4
TF2 Hitman's Heatmaker (Nerf blaster mod from Sillybutts Foxbat) — zdjęcie 1
1 / 4

TF2 Hitman's Heatmaker (Nerf blaster mod from Sillybutts Foxbat)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

methanejuice

methanejuice

@methanejuice

It's a Nerf blaster remix of the Foxbat from Sillybutts to the appearance of the Team Fortress 2 Hitman's Heatmaker

Ocena
0 / 5
Polubienia
45
Pobrania
48
Wydruki
0
Wyświetlenia
1038
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike
SzczegółyPliki (76)Wydruki i komentarze (Wydruki: 0) (Komentarze: 0)Remiksy (0)Kolekcje (52)Powiązane

Thanks if you want to buy me a coffee :) https://buymeacoffee.com/methanejuice

You need the original Foxbat kit, plus the following:

https://docs.google.com/spreadsheets/d/1KOiNNJb-DsYRX4Xing8HacSmP-WwXPeXNfO9-ASy6mA/edit?usp=sharing

Assembly guide:

  1. Assemble the bolt like the original Foxbat. (M3X16 qty 2, M3X30 qty 1)

  1.  Assemble CatchHolder and PlungerGuide with qty 3 #4 screws. Add the Catch with two small springs from the kit. Cover with CatchHolderPlate using qty 2 #4 screws

  1. Assemble the FrontBlock_NoSights piece plus the StraightTalon_TriggerBar, TriggerYoke, and CatchPusher,  using the two small pins, M3 square nut and 10mm screw, and the Clevis Pin, like the original Foxbat.

  1. Add in the plunger tube and main spring,  the BackBlock, and the small spring in between for trigger return 

  1. Add the Trigger Joint piece with qty4 #4 screws. Add the Turnaround with all the orings like how the original Foxbat was assembled (Dash123 O-ring qty 2 and Dash016 O-ring qty 2)

  1.  Assembled the barrel and the BarrelCover piece using qty2 M3 30mm screws

  1. Add the  Trigger extend piece with qty 4 #4 screws

  1.  Assemble both sides of the rare furniture, using qty 4 on both sides, indicated locations, 8 total

  1. Assemble the Trigger with qty 1 #4 screw, plus the StraightTalon_GripBottom_Shorter_HH from the back, secure both sides with qty 4 #4 screws

  1.  Add Center Joint piece in the green location, qty 2 ball detent in blue locations, and qty 2 #4 screws in red locations

  1. Install StraightTalon_GripTop and DartGuide, using qty 2 #4 screws each

  1. Attached SlideBack_NoIronSightsto the CatchHolder with qty 5 #4 screws. Install the RAM with qty 4 #4 screws

  1. Add the front bit of the grip furniture using qty 5 #4 screw on both sides

  1.  Assemble the trigger guard section with the Aft and Front Linkage, the StraightTalon_GripBottom_Shorter_HH, and the Outerlinks. Secure with qty 4 #4 screws each on both sides in the purple locations. And secure with qty 1 M4x25mm screw and nut to link the grip with the Front Linkage

  1. Cover the grip with Side Pannel_R &L on both sides, secure with qty 4 #4 screws

  1. Install the Fake Barrel_Front v2 with qty 6 #4 screws

  1. Add Fake Barrel_Back with qty 2 #4 screws, assemble onto the Bolt core the following parts: Bolt cover with qty 4 #4 screws, Bolt with qty 1 M4x70mm screw and nut, StockRing with qty 2 #4 screws

  1. Add Stock_slideV2 with qty 4 #4 screws

  1. Assemble the stock using qty 14 M4x45mm screws and nuts

  1. Install the Cheak rest, StoclButt, and Stock_Joint using qty 10 #4 screws

  1. Install the Scope bracket 1 &2 using qty 8 #4 screws

  1. Assemble the RangeFinder as the image shows; cut a section of filament and place it in the red location to keep the parts aligned. Secure the parts with qty 3 #4 screws

  1. Install the range finder and the falke decal screws with qty 4 #4 screws

  1. Install the Supressor parts, safety tip, and parts for the scope (needs glue in between) with qty 6 #4 screws

Tagi

nerfteamfortress2tf2nerfblaster