Adjustable Door hinge jig for 50mm (2") to 102mm (4") hinges
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A pair of jigs that adjust to the actual hinge width to cut the rebate in the door edge and door frame.
- Ocena
- 0 / 5
- Polubienia
- 1
- Wydruki
- 0
- Wyświetlenia
- 271
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Standard Digital File License
I recently had quite few doors to hang and decided to create a pair of jigs to speed up the process (ignoring design and print time!!). Different hinges were involved so I needed the jig to be adjustable.
This pair of jigs enables a router fitted with a 5/8" or 16mm cutter and attached to either a 100mm or 4"(101.6mm) baseplate to quickly cut hinge rebates in a door edge and the door frame (lining). Both jigs are quickly set to the actual hinge width and support the typical door hinge range of 50-105mm (2-4" approx.). The design is accurately set to a 5/8" cutter; if a 16mm cutter is used it will only make approx. 0.12mm difference (wider) final cut width. The individual STL files shown are all for the 4" baseplate version- my 4" baseplate and edge limiter jig for the Dewalt DC600 router can be found here
https://www.printables.com/model/1579276-dewalt-dcw600-4-baseplate-and-rebate-fence
If you have a router fitted to a 100mm baseplate rather than 4" one please download the zip file that has all the relevant STL files for that size (except for knobs- download them).
The jigs are secured using 35mm M6 bolts, washers and a printed 20mm knob - two knob designs are included, each with the option of printing with a captive M6 nut or using a M6 threaded insert. These knobs do not foul the router when used.
The photos show the typical sequence to use each jig.
Door Edge jig.
First set the width of the jig to suit the hinge - position the hinge against the reference stop and tighten the assembly (photo 3).
Mark on the door edge the hinge position and align the jig to the mark (photo 4). Attach the jig to the door edge using a panel pin in each end (clamps can also be used but not normally needed). The pins do not need to be hammered in too far. The jig has storage for 6 pins.
Set your router and fence to the required depth and edge offset (photo 5) and cut the hinge recess (photo 6). The hinge recess has a 5/8radius which may be correct for some hinges (photo 7). Use a chisel or cornet tool to square the cut is needed (photo 8 & 9).
Frame jig.
The frame jig can be set to the required width in two ways. If the door edge jig is already set, this can be located in the frame jig holes and the frame jig assembly tightened (photo 10). This is the preferred method, as the jigs can stay paired when the frame jig is initially positioned on the wood. Due to the depth of the frame jig there can be some flex; the door jig ensures adds rigidity to keep the width accurate. The alternative method to set the frame jig is shown in photo 11.
Once the frame jig is set, position it so that the position of the hinge marked on the frame is aligned to the two alignment tools and fix with pins (photo 10). The design allows the frame jig panel pins to be fitted with the door jig in place. The frame jig is vertical, so to better retain it in place use the two screwdown fixings as shown in photo 13. These screw holes will be hidden under the final door lining trim. Use the router as before to cut the hinge rebate.
Once finished, the jig can be stored together as shown in photo 15.
If you are wondering.....I made a final small design change and didn't have enough yellow to reprint the frame jig, so used red.
Printing
This can be printed in PLA or any stronger filament - I used PETG at 0.2mm layer height, 3 walls, 20% infill (cubic), Support enabled - Tree Hybrid on build plate only.
The slicer screenshots show the best orientation to print the parts for strength. The mortice part of the door jig does need supports under one area - Tree hybrid works best for this.
To simplify printing and reduce the need for supports the frame jig alignment lips are printed separately and glued in place.
20mm knobs - there are two knob designs and each can be printed to accept either a captive nut or threaded insert. Two knobs are needed (one per jig) . If using the captive nut option, print these separately to any other parts and set your slicer to pause at the layer just before the hole is closed (approx 7.68mm height). Insert the M6 nut and continue the print. Do not enable supports when printing the knobs.
