1/4 Scale Federal Sign and Signal STH-10 Siren
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
DC powered 1/4 Scale outdoor warning siren. Based off the former Independence Iowa STH-10 that I now own.
- Ocena
- 5 / 5
- Polubienia
- 7
- Pobrania
- 70
- Wydruki
- 0
- Wyświetlenia
- 509
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial
DISCLAIMER
The information provided here is offered on an AS-IS basis only. While I have efforted to make this helpful to you, I do not offer any warranty or guarantee of any kind regarding any aspect of this information. The information below may be subject to change without notice. The full risks as to the use of this information are assumed solely by the model builder.
This can be printed on smaller printers (220x220)
To Assemble this model you will need get these or equivalent.
https://www.amazon.com/dp/B0F1Y5Y624 2.3 to 4mm coupler
https://www.amazon.com/dp/B0BB2V8PNK 390 Motor
https://www.amazon.com/dp/B0D2XCH9R2 10F super capacitor
https://www.amazon.com/dp/B0BX7HNJTJ Power Regulator
The Impeller and drive hub are held together with M3 bolts.
again like with my other models, Unless noted, I don't use threaded inserts. Normal bolts will cut their own threads into the plastic the first time you put a bolt into them.
there are two version of the stand... one that has parts that will fit larger printers and another that will fit smaller printers
There is a hub for mounting the impeller to the motor. The 2.3 to 4 mm coupler mounts onto the 390 motor. The rotor hub press fits on the 2.3 to 4mm coupler. There are holes in the hub to line up with the set screws on the coupler. Back out the screws on the 4mm end to lock the hub on the coupler. The impeller fits over the rotor hub. The rotator drive hub goes onto the intake side of the impeller. M3 bolts go through both hubs and the impeller and holds everything together. If you ruin the hub in anyway you can reprint the hub without doing the whole rotor. The impeller itself has holes in it around the circumference to allow for M2 bolts to be used for balancing if need be
The motor holder mounts on the stator. Both the stator and motor mount have insets to press M4 nuts into them... The mount then bolts to the stator. The motor will slide into the mount and will be held buy the 6 M4 bolts
To align the motor in the stator... those six screws in the motor holder adjust the placement and tilt of the rotating assembly. You need to adjust each screw to center the rotor up. For each screw you tighten on the top, you need to loosen another one on the top, same for the bottom as well. The assembly will move in the direction that the screw is pushing it
If you have that 390 motor I linked above you can take a second coupler and put it on the back shaft and use it to give the rotating assembly a finger spin to check for rubbing. Just keep at it until you find the sweet spot. It takes myself about 5 minutes to get it dialed in.
If you want to put screens between each horn and chopper port, you can use some window screen cut to size
The power regulator is the standard higher power unit I use. Set to 3.5 volts for siren speed. You can stuff the 10 farad supercap into the power box if it won't fit under the motor cover. Simply wire it into the circuit for longer wind downs. For a power source a standard wall wart will not work. You'll need something that can source 3 or 4 amps because if the voltage on the supply drops to a certain point the power regulator will shut down and the siren will never get up to speed.