1 / 19
Prusa i3 MK2S 80mm PSU Fan Mount (2 options) — zdjęcie 1
1 / 19

Prusa i3 MK2S 80mm PSU Fan Mount (2 options)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

At the request of mrhappydude I put together a PSU fan mount for the MK2S.

Ocena
5 / 5
Polubienia
22
Pobrania
140
Wydruki
2
Wyświetlenia
1299
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

At the request of mrhappydude I put together a PSU fan mount for the MK2S. This initial version isn't for a 120mm fan as he requested, its for a 80mm fan instead (I didn't have any 120mm fans handy).

Option 1:
This mount should support any 80mm fan, 10mm-25mm deep with its adjustable nature, fitting a 120mm fan might be a challenge as the case is less than 100mm across...

You need to print:
1x - Fan Shroud for Clips.stl
4x - Fan Shroud Clip.stl

Option 2:
I had another idea stuck in my head for this part which I also just completed and tested...
its a minimal version which prints fairly quick and lets you use any 80mm fan shroud/screen you want, but its a little tougher print... at a minimum its just 4 pegs that lock into the case that have threaded shafts and thumbscrews to hold the fan in place.

You need to print:
4x - Fan Shroud Grill Peg-thumbnut.stl
1x - Fan Shroud for Pegs.stl (only if you want to use the bundled shroud, else use can omit)

Comments greatly appreciated, let me know what you think!

Print instructions

Category: 3D Printer Parts Print Settings

Printer Brand: Prusa

Printer: i3 MK2S

Rafts: No

Supports: No

Resolution: .15 Optimal

Infill: 100%

Notes:

All tested parts printed in ColorFabb NGen (as I have lots) I'd normally print this in PETG, but PLA should be fine as well. 100% infill vs 20% only changes the filament use by 10cm or so, you could try it at 20%, but the few mm of savings isn't really worth it.

Post-Printing

Build & Assembly Notes:

General:

  • I'd align the clips so the teeth are printed on the X-axis (long side front to back) or the pegs so they line up left to right to maximize the resolution as the X-Axis has the least momentum, but either orientation works (I printed both to test).
    Assembly:
    Option 1:

  • press the 4 printed clips into the shroud, they should ratchet into place, only push them about half way in. Look at the teeth and orient the top and bottom as required.

  • Push the fan into the shroud, it'll lock on the pins
  • Place the assembly on the side of the power supply and rock/move it side to side, top to bottom until the 4 clips pop through the PSU and lock in place, take your time, it doesn't take pressure, just movement.
  • keep rocking/pressing the assembly towards the PSU until it ratchets as far as it can and is tight.
  • if you're concerned about it coming loose.... yep... the hole in the end of the clips is just the right size for a little piece of filament to go in... put that in and they can't pop back out...
    Option 2:

  • figure out which slots line up with the fan holes you need.

  • The top pegs catch on the top edge of the upper slot you figured out, then let them drop down, they won't fall out.
  • then its easiest to put the bottom two pins through the fan and just start the thumbnuts, then catch the 2 lips of the pegs on the bottom edge of the lower slots.
  • rotate it up and which will keep the bottom ones from falling out and onto the top pegs, put on the last 2 thumbscrews and tighten them all up.

    How I Designed This

Option 1

Option 2

Revisioning:

v1.0 - Initial upload
v2.0 - added a second mounting option.

Tagi