1 / 9
1:29 Scale Southern Pacific EMD SD9 G Scale Locomotive — zdjęcie 1
1 / 9

1:29 Scale Southern Pacific EMD SD9 G Scale Locomotive

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

1:29 Scale Southern Pacific EMD SD9 G Scale Locomotive with ex-SP and non-SP options.

Ocena
0 / 5
Polubienia
24
Pobrania
164
Wydruki
0
Wyświetlenia
920
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

THERE IS MORE TO COME - photos and instructions.

NOTE: I accidentally included some redundant files: "Body A", "Body B" and "Body C" are identical to "Long Hood Section A", "Long Hood Section B" and "Long Hood Section C". All I did was rename them but neglected to remove the original files. I have since removed "Body A-C".

UPDATES TO FILES:

13 July 2026 - Uploaded document with detailed build instructions and removed previous instructions.

14 May 2026 - Updated the "Non-Dynamic Roof" with openings under the smokestacks and an integrated speaker mount.

3 May 2026 - Added some new options for my SD9 design.

Non-SP Radiator, Long Hood and Short Hood - Does not have the Southern Pacific light package.Ex-SP Radiator and Short Hood - Used to have the SP light package but the Gyralites and Emergency Lights are removed.Non-dynamic roof section - replaces the Dynamic Brake Blister.

12 Feb 2026 - The Radiator was missing the holes on the top for grab irons. I added the holes and uploaded a new version 12 Feb 2026. Otherwise, they are easily drilled.

10 Apr 2026 - Updated the files "Dynamic Brake Blister" and "Dynamic Blister Roof Extension". Added a flange that will accept two M3 bolts that will more effectively hold the two parts together.

12 Apr 2026 - Updated "Cab Steps" to add slots/holes for two 3mm LEDs to be installed as "ground lights."

17 Apr 2026 - Added a file "Class Light Ring" which is a small ring that fits into the Class Light opening. It is optional. If you want to use it with a 5mm LED, you will have to grind down the outside of the LED by inserting it into a drill and file the LED surface down to fit into the ring. Otherwise, you may just insert the LED directly without modification into the Class Light opening without the ring.

20 Apr 2026 - Uploaded a new version of "Cab Steps" which has larger openings and notches to accommodate the wiring for "ground lights."

23 Apr 2026 - I added two new files: "RailPro holder" and "Blunami holder."

Here is a video of a completed model running and pulling cars: https://www.youtube.com/watch?v=zIHXUSzJ6Jk
Here is a video of the prototype running: https://www.youtube.com/watch?v=gmJJkcrUjpw

This is a 1:29 Scale Southern Pacific EMD SD9 Locomotive. All body, base and truck parts are 3D printed. It uses two USA Trains R22-422 3-axle motor blocks. This design does NOT require any additional hardware or electronics from USA Trains.

I use battery power in all of my 3D printed locomotives, therefore I always remove the "skates" from the USA Trains R22-422 motor blocks.

NOTE: If you want to use track power, you should leave the "skates" in place. For track power applications, the 3D printed side frames do not include the necessary journal bushings with soldered wires to allow power from the wheels to flow through the axles to the "track power" pin on the motor block. These bushings are not sold individually by USA Trains, but can be obtained by cannibalizing them from a set of SD40 truck side frames (which CAN be purchased from USA Trains). The method of attachment of the journals to the 3D side frame is yet to be determined. Perhaps someone will modify the design to do this at some point.

I recommend printing at 0.10mm layer height, particularly for the side frames. It takes longer, but well worth it.

Some of the materials needed to complete the model:

  • MF63ZZ Flange Ball Bearing 3x6x2.5mm Full Complement Bearings - quantity 8

  • USA Trains R22-422 motor blocks - quantity 2

  • M3 and M4 bolts in a variety of lengths.

The power trucks use a "center pivot," which is completely different than the way USA Trains mounts these trucks. (I use the exact same motor mounting method on my Krauss-Maffei design.) The "floppy axle" is left unconstrained (not attached in any way to the loco body.)

The axles ride in stainless steel roller bearings that are epoxied into the 3D printed side frames. The side frames are screwed to the 3D printed motor bracket. Metal foil is used to reduce wear on the surfaces that rub together under the frame. The trucks are attached to the base using M4 bolts and washers.

Tagi