Prusa Core One Cabinet Fume Manifold to a 120mm Flex Pipe Exhaust
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This duct adapts to the Core One back plate to vent air exhaust to 120mm flexible pipe at the right rear of the cabinet.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 52
- Wydruki
- 0
- Wyświetlenia
- 363
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Model is probably an overkill, but I like the aesthetic of piping and was an interesting cad design exercise whilst waiting for the delivery of my Core One and then getting the Mk3.5 to build it for its successor.
The main design purpose was to allow ventilation of the fumes/particulates from the print chamber with minimal space impact between the back of the cabinet and the wall. An extra bonus was that when I plugged it onto the Core One there was a very substantial reduction in noise from the Cabinet Fans.
The design tried to linearly ratio up the cross-sectional area along the duct from the Cabinet fans to the 120mm flexible pipe connection.
I have used it now for about a week and after finding out how to tweak the cabinet temps in Slicer and it does get rid of the ASA smell to outside. (I tweaked the ASA slicer nominal temp from 55 to 53°C and fans seem to be on constantly but varying in speed - chamber seems to sit at about 56°. see pic of slicer setting)
I preferred to have my 120mm flexible exhaust to the window out the way to right rear, but the Part 1 duct piece should be able to be mounted the other way (left rear) if you need but it will make the outlet slightly lower. I may get around to mirror the design to match the exit height.
Update 9 March 2026 :- I have uploaded a left vent option Part 1 duct piece.
Update 11 March 2026:- I have included a 125mm flexpipe joiner option (to match an update to my air duct valve model)
I have included an optional mesh plug part for placement between the outlet of the Part 2 duct and the Flexpipe joiner. I tend to unplug the 120mm flexpipe when printer is not in use to minimise the risk of strong wind and rain forcing its way to the printer, so the mesh plug is just there to stop me dropping foreign objects into the outlet (might keep the spiders out too).
I have endeavoured in the design to allow a MMU to fit at the back (I may shift mine from my Mk3) using dancan13f's MMU adaption (Printables Model 1283543) but note that I haven't yet verified with a physical check. (One of my photos show the MMU mounting strip in place). Perhaps I may be tempted to use the forthcoming INDX upgrade instead.
Also to be done is to make a slightly modified version to suit the Core One L (Screw holes on the back of the L are displaced vertically)
Printing
With 55° temps in mind, I made mine in PETG (PLA likely would sag). If you prefer you could use ABS/ASA but may be more temperamental to print (I did manage to print a reasonable ASA version of the Part 1 duct piece in the new Core One.
The 2 main parts of the duct consumed about 200g each of PETG when I printed mine. (Printed on the Mk3.5 without any draft shielding, subsequently did print an ASA version later when the Core One was running but the PETG version stays as I think it looks better)
Supports will be necessary for the 2 duct parts (see photos). I used organic supports with the Slicers paint on supports. Don't be too aggressive with print speeds. Use a 0.6mm nozzle &.25mm layers if you have one to speed up the printing however it works OK with 0.4mm nozzles.
I found with my PETG print (on the Mk3) the outlet of the Part 2 duct resulted in about a 1mm out of round distortion (just the way the plastic layering behaves) so you may have to "spring" it into the Flexpipe joiner (or optional Mesh_plug) or slightly reduce the diameter of the joiner/Mesh_plug when slicing.
Assembly is with suitable 3mm screws mounting the Part 1 onto the threads on the back of the Core One whilst sandwiching in the Cone part (optional - you can't see them). One of the top screws is a little awkward but the small end of the hex key can fit to tighten. 3mm screws and nuts are used to mount the 2 duct pieces together.
Other Models that interwork with the extraction Manifold that I used with my setup
Air Duct Valve
Window Exhaust Vent