Refinement of Electric Hurdy Gurdy and new P90 soapbar pickup housing
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
My adjustments of the original design that increase the strength of some parts and allow for flexibility of pickups used
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 20
- Wydruki
- 0
- Wyświetlenia
- 249
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Music
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Hark! Weary traveler! Sit a spell and allow me to regale you with the tale of embarkation to luthiering a hurdy gurdy using the quite remarkable bit of engineering dropped by demagnetized and subsequent mods by dablob, and how I've made my own additions/adjustments to fit my needs.
First, this was intended as a gift and as a fun project for me to tackle and hack. Since it was a fun time thing, I actually didn't document all of the hacks that it took to get the instrument together, but I did make extensive use of the wisdom found in the comments of demagnetized's original posting.
With that out of the way, here was the vision for the outcome: I wanted to embrace the futuristic renaissance of this ancient instrument while adding some whimsical black death elements. To that end, I used transparent petg and orange abs-gf for strength and to make full use of 3d-printing's "futuristic" aesthetics. For the keys, I went with tough pla since they needed to have some resilience/toughness.
Everything was printed on a P1S with bambu filaments.
Further adjustments I made to the assembly process was to use Wago quick disconnect wire clamps so the pickup module could be easily removed from the wheel and electronics section.
Essentially all other assembly suggestions revolve around the drive train:
Since I used a 1/4-20 threaded rod as the drive shaft, a lot of the drive components fit snug and self tapped, but to endure the torque without slippage I filed a flat into the rod where the wheel's set screws could bite. For the retaining ring/bearing mate cap that sits beneath the pickup, I actually drilled through the rod to create a passthrough for the set screw holding the cap on. This was much more reliable than the friction of set screws and allowed me to countersink the head of the screw since the pickup set up I went with had a pretty tight fit with the retaining ring.
I had printed the wheel in ABS-gf and was worried that pine rosin terpenes could eat away at the plastic. So after printing the wheel, I used some hardwood veneer edge banding from the hardware store to improve the friction for the strings while not having to question the rosin use.
Since I had a donor pickup, electronics, and nice volume and tone knobs, I drilled out the center of one of the knobs I had printed and fused it to the crank with some acetone to make a standoff. Then I used some CA glue to drop the captive nut crank plug into the knob/crankarm. When the arm was assembled, I put a little blue thread locker on the 1/4-20 rod and then hand tightened the arm until it seated. It is important to be conservative in tightening the crank arm cause I ended going too far and cause the leech to slightly delaminate. After that I used a second threadlockered nut onto the threaded rod as a stop before screwing on the crankarm.
To connect the knob to the crankarm I used a threaded post and screw with a smattering of washers.
Credit is due to https://www.printables.com/model/1433085-the-dark-doctor-plague-doctor for the crank cover finial, which has not been included in these files but I used in my personal construction as a decorative element.
