1 / 3
Ultimate 140W FPV Power Bank Case (PD 3.1 28V 5A / 2-6S LiPo) — zdjęcie 1
1 / 3

Ultimate 140W FPV Power Bank Case (PD 3.1 28V 5A / 2-6S LiPo)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

140W PD 3.1 FPV Power Bank for 2-6S LiPo. Active 50mm cooling, sandwich case, no supports. Ideal for mobile soldering.

Ocena
0 / 5
Polubienia
13
Pobrania
47
Wydruki
0
Wyświetlenia
403
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution

Ultimate 140W FPV Power Bank Case (PD 3.1 28V 5A / 2-6S LiPo)

This is a rugged, active-cooled housing for the 140W Bidirectional PD 3.1 USB-C Module With XT60PW-M connector. It turns your 2S–6S FPV flight packs into a high-performance power hub, ideal for field charging and high-power bench tools.

Why this design?
  • Mobile Soldering Power: Perfect for high-end mobile soldering irons (TS101, Pinecil, etc.) that require a full 140W output (28V 5A max) for the fastest heat-up times.

  • Active Cooling: To handle the heat of 140W power conversion, this case features a dedicated housing for a 50mm fan with a Voronoi grille to prevent thermal throttling.

  • No-Support Print: Optimized for 3D printing. All cutouts and ports are designed to print cleanly without any supports.

  • Secure Sandwich Design: The PCB is securely held between the top and bottom lids, ensuring the XT60 and USB-C ports remain aligned even with repeated plugging/unplugging.

Power & Charging (Important!)
  • NO BALANCE CHARGING: Crucial Safety Note: This board does not have a balance circuit. It charges the battery pack as a whole through the XT60 connector. Only use high-quality, well-balanced packs. If your cells become unbalanced, you must use a dedicated balance charger.

  • Current Draw (Max Output): * 6S Pack (~25V): Draws approx. 5.6A.

    • 4S Pack (~15V): Draws approx. 9.3A.

  • Charging Warning: Since the board is bidirectional, it will attempt to charge your LiPo at the full 140W if connected to a high-power USB-C brick.

    • Small Packs: DO NOT charge via USB-C. Use an external balance charger. 140W is too much current for small racing packs.

  • Power Limiting: You can limit the input/output power to 100W or 65W using the solder bridges on the PCB.

Critical Setup: DIP Switch Settings

IMPORTANT: Configure switches BEFORE connecting a battery.

  • Switch DOWN = Active (ON)

  • Switch UP = Inactive (OFF)

Configuration

Battery Cell Count (Select One)

Cell Full Voltage (Select One)

6S

Set 6S to DOWN

4.40V (LiHV): Set 4.4V to DOWN

5S

Set 5S to DOWN

4.35V (LiHV): Set 4.35V to DOWN

4S

Set 4S to DOWN

4.20V (Standard LiPo/LiIon): Set 4.2V to DOWN

3S

Set 3S to DOWN

4.10V: Set 4.1V to DOWN

2S

Set 3S AND 4S to DOWN

3.65V (LiFePO4): Set BOTH 4.1V + 4.2V switches to DOWN

Hardware (BOM) & Assembly

Bill of Materials

Category

Item

Quantity

Specifications / Notes

Electronics

140W PD 3.1 Module

1

Bidirectional USB-C with integrated XT60.

Electronics

5010 Fan

1

50x50x10mm (Can fit up to 15mm). 24V recommended for 6S.

Electronics

Fan Connector

1

2-pin JST-XH (2.54mm pitch) to plug into the board.

Hardware

Fan Screws

4

M3 (16mm to 20mm length).

Hardware

Fan Nuts

4

M3 Locknuts (Standard M3 nuts also work).

Hardware

Case Screws

4

M2 (10mm to 20mm length) to secure the lids.

Filament

High-Temp Filament

~50g

PETG, ASA, or ABS. (Do not use PLA).

  • Fan: Designed for a 5010 axial fan (50x50x10mm). It can accommodate fans up to 15mm thickness, though fitment for 15mm is not guaranteed.

    • (Note: 24V fan recommended for 6S compatibility).

  • Case Assembly: Mount the fan to the top lid using M3 hardware, connect the fan plug to the board, and place the PCB at an angle to set switches in the case cutouts. Then use 4x M2 Screws (10–20mm) to drive through the bottom lid into the top lid, sandwiching the board.

Print Settings
  • Material: PETG, ASA, or ABS (Required for heat resistance at 140W).

  • Supports: NONE.

  • Infill: Any 15-40% (Rectilinear preferred).

  • Walls: 3-4 Perimeters.

Safety Warning
  • No Balancing: This device does not balance your cells. Periodically check your battery on a dedicated charger.

  • Polarity: Triple-check your XT60 wiring. Reverse polarity will destroy the board instantly.

  • Active Cooling: Do not operate at 140W for extended periods without the fan running.

  • Disclaimer: This is a DIY project. Assemble and use at your own risk.

Tagi