1 / 2
Grip Moulds and Moulding Stand for Turn Racing 488 Challenge — zdjęcie 1
1 / 2

Grip Moulds and Moulding Stand for Turn Racing 488 Challenge

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Moulds and moulding stand for the Turn Racing 488 Steering Wheel Project

Ocena
0 / 5
Polubienia
5
Pobrania
18
Wydruki
0
Wyświetlenia
183
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial

Moulds and Moulding stand for the Turn Racing 488 Challenge Project

Create moulded polyurathane moulds with these models. This includes a moulding stand which you can mount your plate and moulds to while you cast them. You'll need to attach the stand to the wheel plate with a 4x M5 25mm bold and nut.

Moulding Grips with Polyurathane Resin

I use the 'Polytek Poly PT Flex 60 Liquid Casting Rubber' which is available here: https://www.mbfg.co.uk/pt-flex-60-rubber.html - you will also need the black dye (which is available here: https://www.mbfg.co.uk/polytek_pigment.html). This has a pot life of around 4 mimutes, so make sure you have everything prepared before you mix up the rubber.

You will need:

  • Water washable resin

  • Cornflour

  • Sanding paper from 180 to 1000 (sanding sponges are ideal for this - https://alishort.com/CUJ6 )

  • Hot glue gun

  • Spring Clamps

  • 2x 500ml plastic measuring jugs for part A and Part B

  • 300my syringe

  • 2ml syringe for the dye

  • Weighing scales

  • Rubber mallet

  • Demoulding wedge or car trim removal tools

  • Silicone spatula for mixing

  • Scalpel

  • Side cutters

  • Kitchen Paper

  • Mould release silicone spray

How To Cast Rubber Grips tutorial

Prepare the Moulds

  • Print off with 4 walls, 15% infill

  • To fill in the layer lines, use a mix of water washable resin and cornflower (mixed 1:1, just paint it on and put on a window ledge to cure in the sunlight)

  • Sand up to about 400 grit

  • Apply high build primer and sand to around 1000

  • Sand the mating faces flat to about 1000

Prep for moulding with Polyurethane rubber

  • Spray with mould release silicone and allow to dry

  • Mount onto the plate and stand upside down (the moulds fill from the bottom) and ensure the front moulds are on the countersunk side of the plate

  • Use spring clamps to hold them moulds on, and make sure they are aligned correctly

  • Use a hot glue gun to seal the edges of the mould

Mixing and injecting rubber

  • You will need to make 300ml of rubber (150g of part A in one container, 150g of part b in another container)

  • Add 1.5ml of black dye to part B and mix (check the instruction for whichever dye you buy - different colour require different ratios)

  • Add part A to part B and mix for no longer than 30 seconds. Mix at a steady pace, if you over mix the pot time will reduce

  • Draw the rubber into a 300ml size syringe

  • Wipe the nozzle of the syringe

  • Inject steadily into the mould

  • Allow it to set

  • Use demoulding wedges or car trim removal tools (you can 3D print these) and a rubber mallet to remove the moulds

  • Trim the flash off of the grips with a scalpel and side cutters

Tagi