1 / 3
Ender 3 Pro Beefy Y (9mm belt/60mm motor/double shear) — zdjęcie 1
1 / 3

Ender 3 Pro Beefy Y (9mm belt/60mm motor/double shear)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This is a replacement motor mount and idler for the Ender 3 Pro to use a 9mm belt, up to 60mm stepper, and double shear.

Ocena
5 / 5
Polubienia
15
Pobrania
42
Wydruki
1
Wyświetlenia
284
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a mod for the Ender 3 Pro (and probably also V2) to improve Y axis performance using:

  1. 9mm GT2 belt

  2. Longer stepper – up to 60mm

  3. Double-shear bearing to support the stepper motor shaft (optional)

BOM and assembly notes:

  1. 16T GT2 pulleys, 9mm (x2)

    1. One for the motor; the side with the screws should be oriented away from the motor body.

    2. One for the idler

  2. 625-2RS bearings (x3)

    1. Two for the idler

    2. One for double shear support on the motor (theoretically optional, but you won't be able to take full advantage of the 9mm belt without it).

  3. M5x30mm dowel pin

    1. For the idler

  4. M5x0.5mm shim

    1. On the pin, between the pulley and bearing

  5. M5x20mm countersunk screw

    1. On the front of the idler

  6. 9mm GT2 belt (approximately 1m)

  7. M5x10mm BHCS or SHCS screws (x8)

    1. To mount the parts to the Y axis 4040 extrusion; longer screws would also work

  8. M5 nut

    1. Trapped inside the tensioner

  9. M3x8 BHCS or SHCS screws (x2)

    1. On the sides of the tensioner (use washers)

  10. M3x35mm BSCS or SHCS screws (x7)

    1. 3 on the tensioner

    2. 4 on the motor mount (use washers if your screws bottom out before they're fully tightened against the plastic part)

  11. M3 washers (x2 or more)

  12. M3x5mm heat-set inserts (x5)

    1. All 5 go on the tensioner

  13. M4x14mm SHCS or BHCS screws

    1. For the sensorless homing "endstop" (optional)

  14. M4 T-slot nuts (x2)

    1. For the sensorless homing "endstop" (optional)

  15. NEMA17 stepper motor

    1. An approximately 21mm or longer shaft is required for double shear support

    2. I'm using this one because I already had it around, but other options might be more suitable: https://www.amazon.com/dp/B00QGBUO1C

Notes:

  1. I printed my parts using ABS/ASA-GF/CF, 7 perimeters but only 15% infill.

  2. All parts can be printed without supports

  3. A 6mm belt could also be used with additional spacers on the tensioner and motor shaft, but the stock belt will not be long enough

  4. The stock Y endstop will not work. I included here an "endstop" that can be installed on the Y axis extrusion towards the back for sensorless homing. If you prefer, you could also design a holder to mount a traditional microswitch endstop.

  5. For reference, I'm getting around 5k input shaper recommended acceleration, but with the belt at only 140Hz over 15cm.

  6. I'm using the following belt clamps: