small travel sized box with lid (vase mode)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
2,24 € – 2,74 € netto (bez VAT)
Dla pliku: N2_small_travel_box_catdad_workshop_47g_1h44m.gcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 2,49 € netto (środek widełek).
- Masa podana przez autora
- 47 g
- Czas druku podany przez autora
- 1,73 godz.
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
A small and sturdy box that you can just toss in you bag and go 🎒
- Ocena
- 5 / 5
- Polubienia
- 156
- Pobrania
- 819
- Wydruki
- 7
- Wyświetlenia
- 2961
- Oceny
- 6
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Share Alike
I got this neat Welly's travel pack of bandages and antibiotic (I hurt myself a lot). It came in a really neat travel tin box. However, airport security really doesn't like you having tin boxes in your bag since they can't see through them with their scanner. This where I designed a similar plastic box, so I can safely chuck it in my bag!
Print instructions
This model was designed to be printed with a standard 0.4mm nozzle, though it will work with a 0.6mm or 0.8mm nozzle as well, so everyone can print one!
Here are some recommended settings and information about the design, to help you get the best print:
- Spiral vase mode / Spiralize outer contour: turn this on, this is how the whole magic works
- Line Width: 0.8mm (this is important, and yes, you can do it with a 0.4mm nozzle)
- Layer Height: 0.3mm (not necessarily required, but anything more and the curves don't work as well)
- Bottom Thickness / Bottom Layers: 1.5mm (e.g. 5 layers at 0.3mm layer height) (this is important to get the best quality bottom with this model)
- Wall speed: 30mm/s (you are pushing a lot of plastic, so a slower speed is best, though if you are confident in your hot end you can go faster)
- Printing Temperature: +10 to +15 degrees hotter than your usual temperature (for example, I usually print PLA at 200, but print this model at 210)
- Flow: 110% (because why not)
- Ironing: turn this on (it is definitely not required, but you get a better surface quality on the inside surface… you can also turn this off to save 10 minutes if you prefer)
- Ironing Line Spacing: 0.4mm (half of the line width should be plenty)
- Ironing Speed: 40mm/s (maybe even faster if you are feeling wild)
Notes
The prints in the photos were printed in Voxelab Yellow PLA+ on a largely unmodified Elegoo Neptune 2 with a 0.4mm nozzle.
Also in the photos
To spice up the photos, I included one of my other models, a larger version of this box.
