The Dawn Vault - Reliquary for the OneBlade
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This is my entry for the Philips OneBlade & Kingdom Come design contest. It is a wall hung display for the OneBlade!
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 37
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bathroom
- Licencja
- Open Community License v1
“Rise, wielder of the One Blade.
Keep thy edge for dawn, till Kingdom Come.”
The Dawn Vault is a wall hung display box to hold your Philips OneBlade.
Compatible with the Philips Oneblade 360 Qp4631/65 Shaver.
This project takes some time to print and assemble! But it's worth it, I promise.
Features:
Compartments where you can store your extra blades and charging accessories

Morning time is often dark, so I included a place where you can mount a cheap (but really nice!) Ikea Kapplake LED spotlight. If you don't want to mount this light, you can simply replace it with the decorative sun that I included.

The spotlight also lights up the stained glass panels from the inside!
The back includes two channels where you can run the LED spotlight cable on the left or right side.

Drainage holes for your OneBlade

Wall mounting slots included on the back for easy hanging to your bathroom wall

All parts are optimized for 3D printing. No supports necessary! No glue required! Including the hinge, wall mounting slots and ornamental details. This means all overhangs are >45 deg, no flat overhangs, and chamfers where necessary to reduce elephant footing so that parts fit together nicely.
Separate parts for MMU/AMS or if you don't have multi-material capability, you can also print parts individually and assemble them. Instructions below!
Designed so that all parts are printable and fit onto a Prusa Core One.

Design Constraints:
I wanted to design something that looked beautiful and was easy to print. Here are the main constraints I followed:
Incorporated stained glass. I think this fits in with the medieval theme really well.
Somehow incorporated the sun from this piece of official Kingdom Come game artwork (because I think it is really beautiful). This is not my artwork! But from the game.

Is modelled and optimized for 3D printing. With no glue required.
I explored a few different colour palettes and I settled on a gold/gilded frame, and two hues for the light rays and blue skies. Of course, you can print this in whatever colour you like.
No AI! I modelled this thing from scratch. It took a while :)
Printing Considerations:
*No supports necessary*
Suggested settings:
0.4mm nozzle, 0.2mm layer height, 25% infill, arachne
Very important! Print external perimiters first then inside perimeters. This is important for the stained glass panels to fit.
I have enabled these settings in the main .3mf for you :) They are here to replicate if you need them.
I have uploaded two .3mf files with all of the parts laid out for easier printing. I have also included each part individually should you need to reprint anything. Open these "as project" in PrusaSlicer.
superheated_reliquary_FRAME.3mf includes all of the non-stained glass panel parts. I printed these in a glossy gold PLA.
superheated_reliquary_STAINED_GLASS.3mf includes all of the stained glass panel parts.
superheated_reliquary_STAINED_GLASS_0FFSET.3mf includes the same stained glass panel parts but each is just offset inwards by 0.15mm if you find that the standard sizes are too tight.
If you have an MMU or AMS, I have included the stained glass panel as one model, superheated_reliquary_glass_mmu_ams, so that you can print this in multi material and save yourself a lot of assembly time!!

Everything is straightforward to print. If you have a 0.25mm nozzle and want a bit more detail, you can print the door_frames and stained_glass_frames (build plates 3–6) with the smaller nozzle for a finer finish.

Assembly:
Parts Required:
Filament for the frame. I prefer a gold colour for a gilded look.
Filament for the stained glass panels. I prefer four separate colours, light and dark blue for the sky, and yellow and orange for the sun. Of course you can use whatever colours you prefer. Or even one single colour. PLA or PETG will both work fine.
This Printables project is really helpful if you want to get super transparent prints for your glass panels. You will need to use PETG.
Any 1.75mm filament cut to 20mm for the hinges. You'll need four pieces.
8x M2.5 x 5mm countersunk screws to mount the hinges. This is the reference I used for my model.
#8 screws for wall mounting.
Instructions:
Print two mirrored copies of the reliquary_back. The entire back is split in two to fit onto the build plate of the Prusa Core One. Both halves are mirrored copies of each other and connected with three of the reliquary_back_tenon pieces. These are a tight fit, and do not require glue. But if you want to add some glue for peace of mind, that wouldn't hurt.

Print reliquary_glass_frame_left and reliquary_glass_frame_right. Be careful that these two are different and unique. Not mirrored as they feature different designs for the sunlight pattern.

If you have an MMU or AMS, simply print superheated_reliquary_glass_mmu_ams, in one piece.
Print the glass panel pieces in superheated_reliquary_STAINED_GLASS.3mf. If you open this in PrusaSlicer, these panels are named according to colour on the side panel. I tested these in transparent PLA.

Mount the glass panels into the frame by pressing them in. They are a push fit and do not require glue. Repeat this for both door halves. Be careful not to push too hard and be patient!

Once the stained glass panel is finished. Print reliquary_door_frame and mount them to the glass panels with 5x reliquary_door_tenon pieces per halve. These are also a push fit and do not require glue.

Print the reliquary_hinge and combine the two pieces with 20mm of 1.75mm filament. This is a tight fit and relies on friction. Do not glue it or the hinge will not work. If the filament slips out, try gluing it on the outside hinge half only, so that the other half can still rotate. Make 4x of these.

Now you can connect the base, doors, and hinges with the M2.5 screws. The holes are undersized so that you do not need heatset inserts. They will self thread into the plastic the first time you screw in the screws. Do not over torque the screws or they will strip the threads! Install two hinges per door.


Mount it to wherever you like with the 4 mounting holes on the back. You don't have to use all four. They are just there for flexibility.

Add your OneBlade and enjoy the Dawn Vault! Thanks for building this :)

Misc:
I modelled this in Rhino3D so if there's interest I can share the original file for easier remixing. I suspect that the stained glass panels could use some fine tuning depending on your printer. I can also share a .STEP file.
Let me know how your building goes! I'm happy to make any changes if parts are too hard to assemble.