1 / 2
QMX Speaker - Easy sound system for your QRP Labs QMX - VE7ZAX — zdjęcie 1
1 / 2

QMX Speaker - Easy sound system for your QRP Labs QMX - VE7ZAX

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

VE7ZAX QMX Speaker - Easy quick speaker project for the QMX. Enough volume for indoor and non-noisy SOTA/POTA use.

Ocena
0 / 5
Polubienia
2
Pobrania
16
Wydruki
0
Wyświetlenia
296
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

VE7ZAX QMX Speaker

Easy quick speaker project for the QMX with enough volume for indoor and non-noisy SOTA/POTA use.   I wanted a simple, tidy, clutter-free way to listen to my QMX without headphones so I whipped up the ear-popping menace.   I'm finding it super handy so it's here to share.


Parts Required:
1 x 28mm 32Ohm speak from Aliexpress - a few dollars...
1 x 3.5mm Stereo plug from Aliexpress - a few dollars for a five pack...
10cm of thin wire.  I used 28AWG

Assembly Instructions:

  1.  Print the speaker enclosure
    I used PETG.  You If you have a skinny power cable you can choose the version that has a removal grip on it.  Otherwise choose the standard one.

  2. Prepare your wires.  Cut two pieces of wire to 25mm(1 inch) in length and tin the ends.

  3. Prepare the stereo plug  - Trim the leads: 
    We only need to connect the tip and the sleeve of the plug so you can trim off the connector that goes to the ring/middle section.  Then cut the other two plugs down short like in this picture.   You don't need to leave much remaining.  Just enough to solder your two thin wires to.

  4. Prepare the stereo plug - Attach the wires
    Next solder the wire to the plug.  Connect the sleeve wire to the edge of the lead if you need to for clearance when you screw it in.  After soldering, test for shorts.

  5. Screw the stereo plug into the enclosure
    Slowly screw the plug in and pay attention to the wires.  You may need to untwist them as you go, this will make sense if you see the wires twisting on the inside.   This is a good time to plug it into your QMX to test your fit.

  6. Connect the speaker
    Now solder the other ends of the wires to the speaker.  One wire to each side.  Last chance for a test so connect it to the QMX and make sure you hear some sound. 


  7. Glue the Speaker to the enclosure.
    Saved the best for last. :)  Use some 5 minute epoxy from the dollar store, or a fancier one if you like, and apply around the inside of the inclosure and to the underside of the speaker.  Check the picture.  I used a toothpick to do this and waited a couple minutes before I applied it so I didn't have to hold in in place too long before it set.  You don't need much to hold this little guy in place so don't go to heavy on the glue.  Hold it in place until it starts to set.  I put mine face down after a while and applied a little pressure while it finished setting.

  8. Done
    That's all there is to it.  Plug it in and give it a whirl.  Please be careful as the excessive SPL produced by this speaker may disturb your neighbours.  Or, more realistically, use it at a talking volume and you're good to go.  If you crank the volume too high you'll start getting distortion so don't do that unless you happen to like distortion...

Hope someone files this useful and thanks for any like and downloads.

VE7ZAX