Adapter to convert Discovery 3300 metal detector to use a DeWalt Battery
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Adapter to mount a Tool Battery on the Metal Detector Handle to use as a power source
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 84
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Gadgets
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Adapter to convert an old Bounty Hunter Discovery 3300 metal detector to use a Dewalt Battery.
The Battery could be used to adapt a mount a different battery.
The platform may fit other models, just keep in mind the provided spacer allows the battery to be connected to the controller for added stability, different models may require a different spacer if that function is still desired.
This conversion will not require mass changes to the controller case
This video was helpful in identifying the wiring of the controller's original dual 9v batteries and gives a different approach to a conversion. They did beautiful finish work. It also presents a different approach to doing the adaptation.
Wires and 9V power
I have included a diagram of the wiring I used. Be sure to validate any wiring config used.
Instead of a fixed car buck converter as the video, I used a LM2596 buck converters. I adjusted one LM2596 to 9V DC from the 19.4V DC my battery was delivering.
I don't know how clean the power is from the LM2596 vs the automotive buck converter. With the super steady power supply of the tool battery the detector is ultra sensitive. I find I have to turn the sensitivity all the way down.
The wires in the current controller are tinned copper or all tin. I don't know if wire TYPE choice influences the effectiveness of the controller. It is after all detecting metal and may be influenced by the metal used in the wires? It could be the over sensitivity I am experiencing is from noise I created by adding the BUCK converter and copper wires in the controller.
My first test after completion showed it did not detect anything. Opening the unit again I found one of the brittle 20 year old wires to the sensor had broken at the board. Keep in mind this conversion could break something and leave the unit unusable.
Other prints I used to complete the task
LM2596 case
https://makerworld.com/en/models/1370275-case-for-lm2596-xl4015-xl6009#profileId-1416620
DeWALT Battery Adapter
https://makerworld.com/en/models/1570773-dewalt-battery-adapter#profileId-1652008
Printing:
My final print version was in ASA which is nice and ridged. (.4mm nozzle, .2mm layer)
I printed a prototype in PETG that had enough flex I added the Zip tie hole in case the battery section needs to be zip tied to the handle.
Exclude the zip tie channel from supports. You will never get them out.
You need to download the DeWalt battery adapter as there are no remixes. It is a beautiful adapter with rugged contacts
Align the spacer and the battery adapter on the plate. Note the spacer should align with the holes the adapter. The ‘bottom’ text is the bottom direction of the battery adapter.
After joining the adapter and the spacer and the battery adapter in the slicer, YOU NEED TO RE-LEVEL the Spacer and DeWalt battery to print flat on the plate. The adapter has an angled front. that will print face down. This assumes you print it spacer end down. Alternately, you could print the separately and glue them together.
Attached the adapter to the control head before using the hole guide.
Careful, the original controller mounting hole towards the battery may have the speaker under it. You likely won't be able to insert the original bolt all the way when using just the adapter (no handle)
Thread inserts:
Add the M5x10 (or size of your liking) into the flat side of the adapter plate. Make sure you don't extend into the curved handle mount side.
If you are attaching your battery to the original controller, add the two M3 inserts into the spacer outer holes
Other printed parts:
The Dewalt battery adapter took 3 M3 inserts
The Buck enclosure took 4 M3 inserts. Also remember if you are gluing and screwing the buck converter enclosure to do that before mounting the board on the enclosure.
When installing the buck converter make sure to mark / know which side is in and which is out.
Materials needed:
(2) M5 x 10 thread inserts
(2) M5 x about 20 FLAT HEAD to attach the battery mount to the adapter. I forgot to measure what I settled at.
(2) M3 x 6 thread inserts
(2) M3 x 8mm with washers
Longer screws to go through the handle to the controller, about 10mm. Mine were 8/32 thread nut inserts in the controller.
Hardware as required by the DeWalt Adapter.
Important Notes
The BUCK converter will ALWAYS draw power when there is a battery connected. Be sure to unplug the battery when not in use.
Disassembly:
The old 9v contacts slide off the plastic edge where they are mounted in the controller body.
There are controller wires under the adhessive control panel above the right side screw. Careful not to break them or your project could end there.
This conversion does involve much modification of equipment and the outcome is not guaranteed. Do this at your own risk.