1 / 10
Fillable master for silicone mold of resin triskelion — zdjęcie 1
1 / 10

Fillable master for silicone mold of resin triskelion

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A fillable mold master for making a decorative triskelion in resin. Requires silicone and resin to complete the project.

Ocena
0 / 5
Polubienia
3
Pobrania
8
Wydruki
0
Wyświetlenia
84
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

This print is a master for a silicone mold of a decorative triskelion shape that I made in green for St. Patrick's Day. The print itself isn't the final product, just its shape prepared to fill with silicone. You need additional material and steps to make the object in the cover picture, but it's not hard once you've done some silicone and resin craft. It's more fun in my opinion than just doing a print.

Note that once you have the mold, you can make more reproductions in craft resin without touching a computer or 3D printer at all. That may not be a great selling point on a site like this one, but you can give it to a friend who does resin craft.

The result looks more handcrafted than printed, and it's unlikely anyone would guess it originated in a 3D printer. There's a trick in step 4 below that helped with the handcrafted look.

Supplies (other than 3D printer)

These are shown in the photo and are easy to find online or in a craft store like Michael's.

  • Platinum cure silicone rubber

  • Epoxy resin

  • Resin dye

Steps

  1. First, print the 3D mold master, which contains a 40mm diameter positive shape. You can probably scale it smaller or larger but I haven't tried.

  2. Fill the master with silicone to the top, making sure you fill above the shape. This is the bottom of the mold.

  3. Let the mold cure (about 6 hours depending on the silicone) and remove it carefully. It may help to go around the edge with a thin screwdriver. Silicone is strong and won't tear if you're gentle.

  4. Optional: Fill the mold temporarily with more silicone, slosh it around, and pour it out. This will coat the sides and pool at the bottom. It covers up 3D print texture and also forms a meniscus, resulting in the art glass look in the photo. It's important that you cure it again before using (another 6 hours).

  5. Now prepare epoxy resin. You'll need less than 10ml total for this size. You can dye it to make the shape visible. I used green for St. Patrick's Day.

  6. Fill the mold with resin, but but only up to the top of the spiral walls. Let it cure (12 hours should suffice).

  7. You can do this before a complete cure if you're careful. Pour a clear layer of resin up to the brim of the mold, or a little higher for a dome.

  8. Now let all the resin cure completely and remove the shape from the mold. The top holds the spirals in place and they are hollow inside.

  9. Optional: You can also mold a cuff that fits snugly around the piece. Use that to bottom-fill the spirals if you want a solid resin object. Use clear resin like you did for the top.

About the design

The triskelion is an ancient design found in many places, not only Ireland, but I felt this green resin piece was appropriate for St. Patrick's day. Traditionally, the spirals are circular in shape but I used ellipses to fit them into an outer circle. To smooth out the design, I started with 3 mutually tangent ellipses and set their eccentricity so they matched the curvature where they are tangent to the outer circle. The final photograph is a figure showing the dimensions. The proof is left as an exercise.

I believe this elliptical triskelion is an original variation of the form, at least with perfect curvature matching.

Tagi