1 / 18
Improved "GT2 Belt Tension Meter 5 Bearings" and case. — zdjęcie 1
1 / 18

Improved "GT2 Belt Tension Meter 5 Bearings" and case.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

I like the GT2 Belt Tension Meter so much I decided to give some away as gifts which prompted a slight design change.

Ocena
0 / 5
Polubienia
9
Pobrania
35
Wydruki
0
Wyświetlenia
235
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

I've really enjoyed the GT2 Belt Tension Meter. I printed up the "5 Bearing" model and it works great. I decide to give a few out to my 3d printing buddies as gifts. With that in mind I decide to make a few improvements as well as make a box for it. Note this is a remix of the original but inspiration was drawn from the many other remixes already on Printables. For convenience I'm including some original files as they are needed to complete the project. All the STLs are original unedited parts (Not remixed) along with the step files for the "BT Meter Spring Block" and  "BT Meter Spring Spacer". All of my modifications have been included as step files. This should allow others to make any changes they feel are necessary.

Required Hardware (Same as "GT2 Belt Tension Meter 5 Bearings" model). All parts are easily found on amazon. 

See assembly details from original. Bearings fit in as seen in the  images. https://github.com/Diyshift/3D-Printer/blob/main/GT2%20Belt%20Tension%20Meter/Manual/GT2_Tensiometer_Assembly_Manual.pdf

Changes:

  1. Slide - Increased the length of the "spring retention" part of the shaft in the slide. The slide is not overall longer, just the tube is longer before it opens up. This prevents the spring from dragging in the path if it begins to buckles under tension.

  2. Slide - Changed the location and size of the retention for the "Calibration Wire Pivot". This keeps it in line with the slide for storage without flopping around.

  3. Slide - Debossed the text to make it easier to read. I print it with a color change to make the text pop.

  4. Slide - Added a 0.4mm hole internal to the post so the slicer will be prompted to add walls increasing the strength of the part. 

  5. Base - Increased the length of the line the needle slides on to prevent it from falling off on either extreme.

  6. Base - Added a hole for a bearing under the needle. The hole includes a shelf to make it easier for the bearing to be placed at the correct depth for proper function. 

  7. Base - Enlarged the hole for the bearing on the underside to accommodate tool use to tighten the nut & screw for the bearing and needle.

  8. Base - Extended the ridge the needle rides along on the gauge. 

  9. Base - Added a 0.4mm hole internal to the posts so the slicer will be prompted to add walls increasing the strength of the part. 

  10. Base - I changed all horizontal fillets to chamfers to increase printability.

  11. Box - Adjusted the size of the shadow cut out approximately +0.5 mm on all sides. 

  12. Box - Changed the shadow portion to include a portion in the hole between the gauge and the body of the meter.

  13. Box - Adjusted the size of the liner parts to -0.125mm on all sides for a tight fit in the box while still loose enough to easily fit into place.

  14. Sleeve - Adjusted the sleeve clearance to 0.125mm on all sides.

  15. Sleeve - Changed the size of the hole to make it easier to push the box out of the sleeve.

  16. Sleeve - Changed the opening by removing the half circular cutout as it allowed dust into the box.

  17. Sleeve - Changed to a thickness of 1.2mm for a sturdier feel and to make it easier to print without any warping.

Tagi