USB Side LED Lamp for Prusa MK4/MK4S
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Orientacyjna cena wydruku pliku
0,56 € – 0,68 € netto (bez VAT)
Dla pliku: usb-side-led-singlecolor_0.4n_0.2mm_PLA_MK4S_30m.bgcode
To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.
Plik i założenia wyceny
Plik użyty do wyceny
Średnia wycena orientacyjna: 0,62 € netto (środek widełek).
- Masa podana przez autora
- 10 g
- Czas druku podany przez autora
- 30,6 min
- Materiał u źródła
- PLA
- Materiał wyceny
- PLA
- Drukarka wyceny
- Bambu Lab P1S - 0.4 nozzle
- Proces wyceny
- 0.20mm Standard
Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.
Zapisane na tym urządzeniu.
Side LED lamp powered by a USB type A socket. Mounted on the Z-axis, so it always shines on the layer being printed.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 91
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v2.0
USB (type A) powered side LED lamp for Prusa MK4/MK4S. Attaches to the X-axis motor. Wire routes out the back and through the X-axis motor wire sleeve into the electronics box. Includes an opening for a power switch.
Most of the lamps I've seen attach to the top frame, which casts shadows onto the plate through the extruder. Not so with this side lamp! Moreover, the lamp is bendable, so you can adjust its position.
Recommended Print Settings
No supports needed
Lay it on the back and make a horizontal cut 10mm above the plate
Add 2 plug-type connectors 1.5mm in diameter
Enable a fuzzy skin (0.1mm thickness) on the ouside walls except for the connectors - this imitates the look of the original orange Prusa parts
To make the USB socket frame a different color, change it for the top 5 layers
Open 3MF file in PrusaSlicer for preconfigured settings
Required Hardware
USB DC buck step down converter 24V->5V
10 Ohm resistor or similar
22 AWG Wire
Power switch (KCD11 10x15mm)
5V USB LED reading lamp of your choice max. 10Watts (2A) of continuous load (see the USB converter specs. for details)
Screw M3x18mm Cap Head Screw
Heat shrink tubing
2 Ring (or fork) terminals
Tools
2.5mm Hex key
Soldering station
Assembly Instructions
Take the switch, resistor and USB converter and solder them one by one in series. Use the USB converter (+) pin. I would recommend not inter-connecting them with wires after all since there is very little space inside the printout. Use the heat shrink tubing to avoid short circuit.
Cut approx. 55cm of the wire. Connect the red wire (+) to the switch and the black wire (-) to the USB converter (-)
Put the back side of the printout on the wire and close it. Use the M3x18 screw to attach it to the x-axis motor.
Put on the heat shrink tubing and solder the ring terminals to the other side of the wire.
Switch off the printer!
Open the printer electronics box, loosen the screws on the top wire holder and pass the wire in from the top.
Unscrew the Power cables and add the rings under the screws respecting the polarity! Your red wire goes under the (+) screw and your black wire under the (-) screw. Close the printer electronics box.
Wrap the wire inside the X-axis motor sleeve.
You're done. Now is the time to test. Plug in your USB lamp and turn the printer on. Test the switch.