Colorful Articulated Snake with Scales
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Fun snake. Now more fun through the power of more colors!
- Ocena
- 5 / 5
- Polubienia
- 103
- Pobrania
- 447
- Wydruki
- 3
- Wyświetlenia
- 1652
- Oceny
- 4
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor Toys
- Licencja
- Creative Commons — Attribution — Share Alike
I imported the original model into the FullSpectrum fork of Snapmaker OrcaSlicer and painted segments with mixed filaments (two versions, for translucent CMY and opaque RYB filaments).
Finally painted in the eyes just cause I could. Because there is no black with 4 colors, the pupils are brown. Anyone with a five-tool-changer can fill that in with black 😁 Or just sharpie them in.
I do not claim anatomical correctness on pupil shape or placement!
This project was saved with FullSpectrum v0.9.4 and printed on SnapMaker U1 (firmware 1.2.0, I don't think that matters).
No raft, no brim, no supports, no cleanup.
Printer Compatibility
Please be advised that the technique behind Full Spectrum requires even more filament changes than a normal multi-color print, so most people would not advise printing this model on a single-nozzle machine.
A Toolchanger such as the Snapmaker U1 or the Prusa XL is the best machine for this, and even then you have to be aware of the additional wear-and-tear. Please decide for yourself whether a colorful print is worth it! It was for me.
Incidentally, if you do have a Prusa XL with the full five toolheads, you could get even more colors! But I don't, so this 3mf is optimized for a four-head toolchanger with exactly the colors I have loaded 😉
Filaments and colors
There are two 3mf projects, one for translucent filaments and another for opaque ones.
The first picture shows a snake printed with Polymaker Panchroma translucent CMY filament and a opaque, chalky white at 0.12 mm layer height at 83% of the original's size. It took 7 hours and looks marvelous, except for the belly (see last pic)[fixed in rev2!].
Because the filament is so translucent, quite a few of the mixes layer solid outer perimeters over inner perimeters of a different color, reducing banding even at higher layer thickness. Hence this project is not suited for opaque color filaments! The white is rarely used in outside perimeters because mine is so opaque.
The second was printed with any old RYB I had lying around (Snapspeed PLA and some matte-blue), before I had the chance to experiment a lot. At 66.67% size and 0.08 mm, it took 6:30 to print. Turned out fine, but I had to dial the number of hues down to 8: the three pure colors and 1:1 mixes between them and the white: Blue, light-blue, green, light-yellow, yellow, orange, pink, purple.
I also shared pictures of the test palettes I printed beforehand to identify good mixes. Yours may very well vary! You should definitely print the palette and fine-tune for your own filaments:
Changelog
translucent rev2:
swap filaments 7 and 8 to fix gradient
solve the irregular bottom layers (especially white bottom perimeters) by painting them with the closest solid filament, see comparison picture. If you modify colors, you might need to use the fill-tool to adjust!
translucent rev3:
reduce the irregular top surfaces (white spots on top scales) by painting specific spots of them, similar to what I did to the bottoms
add shorter snake with just one full gradient from blue to purple
saved with FullSpectrum release 0.9.9
(I'm not updating the "opaque" version because I'm not using it; let me know if there are problems opening it in newer versions of the slicer and I can try to upgrade it, but I don't see any need to make changes)