1 / 2
Dual Fan version of BC-250 ATX CASE with backplate cooler — zdjęcie 1
1 / 2

Dual Fan version of BC-250 ATX CASE with backplate cooler

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Widened case for BC-250. Added 50mm width to fit a custom backplate cooler. Functional but rough DIY remix.

Ocena
0 / 5
Polubienia
2
Pobrania
107
Wydruki
0
Wyświetlenia
1788
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

DISCLAIMER: This is a very rough, amateur remix. It is a "function over form" project with several fitment issues, but it works great for thermals.

I modified the "Dual Fan version of BC-250 ATX CASE" to add about 50mm of extra width. My goal was to fit my BC-250 equipped with a custom backplate cooler (https://pl.aliexpress.com/item/1005006009318799.html?spm=a2g0o.order_list.order_list_main.144.76641c24fEmV5K&gatewayAdapt=glo2pol) and give it enough breathing room. I did this in a very amateur way, but it works, my BC-250 maintains very good temperatures.

Please be aware of the following issues before printing. Here is how I solved them:

  • Motherboard Rails: The rails meant to hold the BC-250 were too tight (maybe due to my modifications). Fix: I just snipped them with flush cutters and the board sits fine.

  • PSU Mount: One of the screw holes doesn't align. Fix: The PSU holds securely on just 3 screws.

  • Front Fan: The modeled screw holes are too big, and standard fan screws fall right out. Fix: I just taped the fan in place.

  • Front/Back Connection: I didn't want to model a complex locking mechanism for the two halves of the case. Fix: duct tape holding it together.

  • Power Switch: Doesn't fit its dedicated hole properly. Fix: A drop of glue keeps it secure.

  • Hub: My specific hub didn't fit into the designated spot.

Hardware & Bill of Materials (What you need):

  • Motherboard: BC-250

  • Fan mount & pressure booster: Download from NexGen3D DIY Steam Machine

  • Fans: 2x 120mm fans (I used Arctic BioniX P120 and Thermaltake Toughfan 12)

  • Backplate Cooler: Custom cooler from AliExpress

  • Thermal Pad: Honeywell PTM7950 (40x40mm)

  • Power Switch: 16mm Flat Head Latching Switch (3V-6V) from AliExpress

  • PSU Jumper: ATX Jumper Bridge from AliExpress

  • Power Supply: Standard ATX PSU (Modular is highly recommended as there is very little room for cable management)

  • Fan Hub: SATA Fan Hub from AliExpress

  • Tools & Supplies: Soldering iron, duct tape, CA glue, flush cutters.

My Print Settings (Printed on Kobra S1):

  • Orientation: Open side facing upwards (towards the ceiling)

  • Supports: None

  • Material: PETG

  • Wall Loops: 4

  • Infill: 20% Gyroid

  • Top/Bottom Layers: 5

If you are good at Fusion, feel free to remix this and fix these issues! If you just want a functional case for your backplate cooler and don't mind using tape and glue, this will do the job perfectly.

Tagi