[Titan] [Clone] LCitan (Low Cost titan case) - v1.2.1
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Some time ago I did two Pitan (https://www.thingiverse.com/thing:2728600) extruders for my printers. These extruders…
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 41
- Wydruki
- 0
- Wyświetlenia
- 398
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution
Some time ago I did two Pitan (https://www.thingiverse.com/thing:2728600) extruders for my printers. These extruders worked very well, but I wanted know if is possible migrate from a Pitan to a Titan e3d cloned.
So I based my research from this thing https://www.thingiverse.com/thing:1727220
I tried to reuse the most count possible of materials, but nevertheless was necessary buy an aditional bearing to use into the idler.
List of materials:
- 1 x Kit Triangelab Gears for Titan: https://www.aliexpress.com/item/32807307266.html?spm=2114.12010612.8148356.45.1f5e55b4Hgpsh9)
- 2 x Bearing 695zz (d=5mm; D=13mm)
- 1 x Bearing MR95ZZ (d=5mm; D=9mm)
- 1 x Bearing 623zz (d=3mm; D=10mm)
- 2 x Screw M3x30
- 1 x Screw M3x25
- 1 x Screw M3x8
- 2 x Screw M3x8
- 1 x Spring 8x15x1mm
- Optional: 1 x bowden adapter (Example: https://www.thingiverse.com/thing:3569343)
Instalation:
It is too easy and intuitive to install, just follow the pictures but remember: there are just 2 things you must not forget:
- Add the M3 nut below body
- Adjust the M3x8 screw to hold the body
Updates:
v1.0.0: 2019 - 09 - 15
Warning: This project is still in progres, I could make works this extruder, but at this moment is a bit difficult to tighten the screws when the top is placed.
Also the turn beetween the gears are not too smoth
I am working in these improves.
v1.0.1: 2019 - 09 - 17
I performed some changes to improve the distance between gears, now the turn is much smooth. I think definitively there is not risk to use the extrusor. Feel free to test it :D
v1.1.0: 2019 - 09 - 21
Uploaded Mirrored versions.
v1.2.0: 2019 - 10 - 1
Added mount to use direct extrusion with Ender 3 (Use mirrored parts for this).
v1.2.1: 2020 - 04 - 16
Reinforced the spring container. After seven months I noted that the PLA had some cracks on that part.
Print Settings
Printer Brand:
Creality
Printer:
Ender 3
Rafts:
No
Supports:
Yes
Resolution:
0.2 or less
Infill:
20% - 40%
Filament: Generic PLA Gray and Red
Category: 3D Printer Extruders